Menu
Your Cart

Boards

Stock: In Stock Model: Fusible-1808FastBlow
Fast blow fuse, to choose from 10A, 15A or 20A.1 unit ..
0.55€ Ex Tax:0.45€
30A Mosfet Module with heatsink and hot bed compatible 30A Mosfet Module with heatsink and hot bed compatible
Out of Stock
Stock: Out of Stock Model: 30A mosfet-module
You can control the current of devices or accessories, such as a hot bed, or different heaters:Maximum current: 30AVoltage: 5 / 12 / 24V 1 Piece..
13.95€ Ex Tax:11.53€
Stock: In Stock Model: Mosfet-30A-Fysetc
You can control the current intensity of devices or accessories, such as a hot bed, or different heaters.Factory testedMOSFET performance: maximum 280AExtra large heatsink, maximum current up to 30A1 unit..
13.25€ Ex Tax:10.95€
32 bit Spider V2.3 board - for Voron - STM32F446 180Mhz 32 bit Spider V2.3 board - for Voron - STM32F446 180Mhz
Only a few units in stock Clearance -35 %
Stock: In Stock Model: Spider-Fysetc-X-Voron
Spider Board is a small but powerful 3D printer control board. In a limited space, it integrates 8 stepper motor drives, 5A 12V power supply, 8A 5V power supply, which provides powerful energy for fans of various voltages, various RGB light strips and Raspberry Pi. You can build a 3D printer with ri..
61.99€ 39.99€ Ex Tax:33.05€
Stock: In Stock Model: Spider3-Fysetc-X-Voron
Spider Board is a small but powerful 3D printer control board. In a limited space, it integrates 8 stepper motor drives, 5A 12V power supply, 8A 5V power supply, which provides powerful energy for fans of various voltages, various RGB light strips and Raspberry Pi. You can build a 3D printer with ri..
69.99€ Ex Tax:57.84€
Stock: In Stock Model: DCDC5V-Module
DCDC power module that supplies power to the electronics 5V circuit.1 unit..
5.75€ Ex Tax:4.75€
Stock: In Stock Model: Octopus
Octopus Board V1.1 from bigtree-tech.FeaturesCartridges Heater: 4Controllable fans: 6Normally Open Fans: 2MCU: STM32F446ZET6 114PinSD protocol: SDIOWi-Fi module interface: Special expansion interfaceCANBus: CANBus with RJ11 interfacePower: HB9500 9.5mm Pitch screw terminals (High current)Three group..
56.75€ Ex Tax:46.90€
Stock: In Stock Model: Octopus-PRO-H446
Octopus Board H446 V1.1 from bigtree-tech.FeaturesCartridges Heater: 4Controllable fans: 6Normally Open Fans: 2MCU: STM32F446ZET6 114PinFrequency: 180MHzFlash: 512KSD protocol: SDIOWi-Fi module interface: Special expansion interfaceSoporte wifi module: ESP8266 (MAX500k7s(CANBus: CANBus with RJ11 int..
63.99€ Ex Tax:52.88€
Stock: In Stock Model: Octopus-PRO-H723
Octopus Board H723 V1.1 from bigtree-tech.FeaturesCartridges Heater: 4Controllable fans: 6Normally Open Fans: 2MCU: STM32H723ZET6 114PinFrequency: 550MHzFlash: 512KSD protocol: SDIOWi-Fi module interface: Special expansion interfaceSoporte wifi module: ESP8266 (MAX500k7s(CANBus: CANBus with RJ11 int..
65.99€ Ex Tax:54.54€
ADXL345 V2.0 - Resonance meter - Klipper 3D printers ADXL345 V2.0 - Resonance meter - Klipper 3D printers
New Out of Stock
Stock: Out of Stock Model: ADXL345 V2.0
Version: 2.0BIGTREETECH ADXL345 V2.0 is a module for 3D printer resonance compensation. It can communicate through USB, greatly simplifying wiring.Main features:The board has a reserved BOOT button for easey firmware updates.Reserved solder points enable users to customize wiring easily.The USB port..
11.35€ Ex Tax:9.38€
Stock: In Stock Model: E3-RRF
E3 RRF Board.Features:High performance main control chip:Packs ARM Cortex-M4 STM32F407VGT6 chip with its main frequency up to 168MHz.Power chip:Adopts AO1284 power chip with the power input of DC 12/24V and maximym output curent up to 4A, greatly reducing power ripple and radiation interference,Inte..
69.99€ Ex Tax:57.84€
Stock: In Stock Model: BTT-CB1
Version: 2.2CB1 outputs signals to the motherboard through the micro BTB two-pin connection, including 100M Ethernet, HDMI, etc. Also, built-in 2.4G Wi-Fi. With its powerful 64-bit ARM Quad Core processor and 1 GB of DDR3 RAM, it has enough power to run Klipper, Linux or Debian.Compatible with Manta..
36.75€ Ex Tax:30.37€
Showing 1 to 12 of 61 (6 Pages)