Menu
Your Cart

Search - stepper driver

Search Criteria

Products meeting the search criteria

32 bit Spider V2.3 board - for Voron - STM32F446 180Mhz 32 bit Spider V2.3 board - for Voron - STM32F446 180Mhz
Only a few units in stock Clearance -35 %
Stock: In Stock Model: Spider-Fysetc-X-Voron
Spider Board is a small but powerful 3D printer control board. In a limited space, it integrates 8 stepper motor drives, 5A 12V power supply, 8A 5V power supply, which provides powerful energy for fans of various voltages, various RGB light strips and Raspberry Pi. You can build a 3D printer with ri..
61.99€ 39.99€ Ex Tax:33.05€
Stock: In Stock Model: Spider3-Fysetc-X-Voron
Spider Board is a small but powerful 3D printer control board. In a limited space, it integrates 8 stepper motor drives, 5A 12V power supply, 8A 5V power supply, which provides powerful energy for fans of various voltages, various RGB light strips and Raspberry Pi. You can build a 3D printer with ri..
69.99€ Ex Tax:57.84€
Stock: In Stock Model: A4988
It is one of the most popular stepper motor controllers, its high performance and low cost makes it ideal for any 3D printer or CNC that use currents lower than 2A.Characteristics: Low resistance Short circuit and overheat protections Rated current 2A Step modes: 1/16, 1/8, 1/4, ..
1.79€ Ex Tax:1.48€
Stock: In Stock Model: DRV8825
The DRV8828 is a driver for stepper motors, with a resolution of 1/32 steps. Datasheet: https://www.pololu.com/product/2133 Heatsink included with thermal tape1 Piece ..
2.25€ Ex Tax:1.86€
Stock: In Stock Model: FYSETC-Cheetah-Board
Current Version: V2Designed for a single extruder 3D printer. Many interfaces are reserved for features such as AC detection, filament detection, leveling with 3Dtouch or other sensors.Features:Compact size: 101.5mm x 72mm. Compatible with the Creatlity Ender 3 motherboard sizeFully integrated all i..
44.99€ Ex Tax:37.18€
Stock: In Stock Model: Gen_L
Versión: 2.1Features:Integrate 2560 and Ramps 1.4  to one PCB, easier wiring and more stable.Use high quality 4-layer PCB.Use Marlin firmware, same configuration way as Ramps 1.4, it can replace Ramps 1.4 directly.Use special power chip, support 12V and 24V.Support a variety of stepper drivers...
24.00€ Ex Tax:19.83€
Stock: In Stock Model: SKIPR
Version: 1.0MKS SKIPR is an all-in-one board launched by Makerbase for running Klipper. It integrates the RK3328 SOC running the Klipper host and the STM32F407VET6 MCU responsible for executing specific machine actions. It meets the use of most 3D printers.Features and advantages:SOC uses Rockchip's..
79.99€ Ex Tax:66.11€
Stock: In Stock Model: S6-fysetc
Actual Version: 2.1The S6 board is based on the STM32F446 32bit mcu has six drive sockets and supports the full range of TMC drives. They have fully extended the resources of the MCU so that you can maximize its power. They considered the possible use scenarios of 3D printers and designed a series o..
54.49€ Ex Tax:45.03€
SKR 2 - STM32F429VGT6  180 MHz - 32-bit 3D Printer Board - Compatible with Marlin 2, RRF & Klipper - STEP/DIR SPI or UART - 12V o 24V SKR 2 - STM32F429VGT6  180 MHz - 32-bit 3D Printer Board - Compatible with Marlin 2, RRF & Klipper - STEP/DIR SPI or UART - 12V o 24V
Out of Stock
Stock: Out of Stock Model: SKR 2
Features:Poweful main control chip:ARM Cortex-M4 STM32F429VGT6 main control chip with a core frequency up to 180 MHz.Compatible with Marlin, Klipper and RepRapFirmwareAdded safety design: Advanced thermistor protection circuit.Thermal runaway circuit protection added.Marlin integrate anti-reverse st..
70.99€ Ex Tax:58.67€
Stock: In Stock Model: TMC2130-SPI
Version V3.0Super silent drivers from Trinamic brand.Version for SPI, is designed for advanced users who know the Marlin firmware and want to test the new features.The special pins have output on the bottom and top, so you can configure the SPI using external wiring, or with the new plates as the Ra..
7.99€ Ex Tax:6.60€
Stock: In Stock Model: TMC2130-SPI-Fysetc
Version V1.2 FysetcSuper silent drivers from Trinamic brand.Version for SPI, is designed for advanced users who know the Marlin firmware and want to test the new features.The special pins have output at the bottom, so the SPI can be configured using the internal wiring on boards such as the SKR 1.4 ..
9.40€ 5.50€ Ex Tax:4.55€
Stock: In Stock Model: TMC2130-STEP/DIR
Version: V3.0TMC2130 - Step / Dir are super silent drivers from Trinamic brand.This is the normal Plug and Play version, compatible with D4988 / DRV8825. You just have to configure Marlin with 16 micropasos, remove the three jumpers from the board and works perfectly.Includes 1 driver + 1 extra long..
7.99€ Ex Tax:6.60€
Showing 1 to 12 of 21 (2 Pages)