Magnetic Heated Bed 220x220mm with inserted Magnets 24V - Similar MK52 / MK3
34.99€
Tax 28.92€
- Stock: In Stock
- Model: HB-fysetc-220x220-24v
Model:
220x220mm
MK52
300x300mm
Magnetic Heated Bed 220x220mm with inserted Magnets 24V - Similar MK52 / MK3
The borosilicate glass has a coefficient of expansion of approximately one third of ordinary glass, it makes it more durable than other glasses to the..
4.99€
Ex Tax:4.12€
The borosilicate glass has a coefficient of expansion of approximately one third of ordinary glass, it makes it more durable than other glasses to the..
5.25€
Ex Tax:4.34€
This is a tough thin plastic film that adheres to the printing base or hot bed.It is designed with a special material in which the printed pieces adhe..
3.15€
Ex Tax:2.60€
Foam thermal insulation for hot bed. It is also a strong acoustic insulator, with great absorption and damping performance.Recommendations:Clean the s..
1.95€
Ex Tax:1.61€
You can control the current of devices or accessories, such as a hot bed, or different heaters:Maximum current: 30AVoltage: 5 / 12 / 24V
1 Piece..
13.95€
Ex Tax:11.53€
Foam thermal insulation for hot bed. It is also a strong acoustic insulator, with great absorption and damping performance.Recommendations:Clean the s..
1.95€
Ex Tax:1.61€
-56 %
All features similar to MK2, you can also operate this board with 12 Volt or 24 Volt Heatbed with 3mm aluminum core. You can print directly on th..
24.99€ 10.90€
Ex Tax:9.01€
-71 %
All features similar to MK2 12v / 24v Volt.Heatbed with 3mm aluminum core. You can print directly on the heatbed, the glass is recommended but no..
35.00€ 9.99€
Ex Tax:8.26€
-52 %
Out of Stock
Hotbed size 220x280 With countersunk holes for screw head, compatible with most Y-axis carriages, including 220x220 or 214x214 bed carriages, because ..
45.00€ 21.50€
Ex Tax:17.77€
You can control the current intensity of devices or accessories, such as a hot bed, or different heaters.Factory testedMOSFET performance: maximum 280..
13.95€
Ex Tax:11.53€
Spider Board is a small but powerful 3D printer control board. In a limited space, it integrates 8 stepper motor drives, 5A 12V power supply, 8A 5V po..
52.70€
Ex Tax:43.55€
Simple, light and precise automatic leveling system.Voltage: 5VCurrent: 15mAMaximum (Peak) Current: 300mAColor: Semitransparent Cable Length: 150..
17.45€
Ex Tax:14.42€
Foam thermal insulation for hot bed. It is also a strong acoustic insulator, with great absorption and damping performance.Recommendations:Clean the s..
1.95€
Ex Tax:1.61€
Only a few units in stock
-13 %
Current Version: V1.1 (TMC2209)Designed for a single extruder 3D printer. Many interfaces are reserved for features such as AC detection, filament det..
40.00€ 34.99€
Ex Tax:28.92€
Check out this bundle
This magnetic bed includes the magnets to be attached to a metal sheet of the same size, on which a buildtak type cover can be mounted. This system is..
Set of components to upgrade from 3DSteel to 3DSteel V2, we recommend visiting our blog for full documentation.It is essential to upgrade to SKR V1.4 ..
Set of components to upgrade from 3DSteel to 3DSteel V2, we recommend visiting our blog for full documentation.It is essential to upgrade to SKR V1.4 ..
Related Posts
23 Dec
2
2024
Perhaps at first glance this update may seem like a minor update, since visually the changes are not very visible, but in reality it is a great update, since we went from 8 to 32 bits, and from 12 to 24 volts. Additionally, we upgraded the controllers from the TMC2130 to the TMC2209 and the bed from an aluminum MK3 to a magnetic bed with inserted m..
18 Aug
0
1092
PID vs Bang BangIf we want to control the temperature of an element of our 3D printer through a heater and a switch, the first thing one could think of is:Select a setpoint temperature.Heat when the actual temperature is below the setpoint.Do not heat when the temperature is equal to or greater than this value.This simple method is the "Bang Bang" ..