Menu
Your Cart

SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D

SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
New -20 %
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D
39.20€
31.50€
Tax 26.03€
  • Stock: In Stock
  • Model: SMARTFIL GLACE 1.75mm

Available Options

It is a filament to which alcohol can be applied and thus achieve different effects. Completely transparent pieces can be manufactured or surface polished to remove rough surfaces and thus achieve a pearlescent effect.

In addition, due to the fusion between layers, the piece increases its structural strength, forming a continuous solid and achieving high tightness.


How to make transparent pieces?


It is necessary to take into account to print pieces of great transparency, which must be pieces of a single layer, so that the alcohol can penetrate homogeneously into the material. If you want to achieve good mechanical resistance, it is recommended to use nozzles of 0.8mm or higher. In this way we will achieve a wall of sufficient thickness to maintain the desired mechanical resistance.


For a greater effect of transparency in the finish using Glace, it is recommended to print using the "Spiral vase" option.


1. APPLY ALCOHOL TREATMENT


Apply the treatment with alcohol (ethyl or isopropyl) with a concentration higher than 70 °. The higher the alcohol content, the faster the process, although it is also more difficult to control. The different application methods are as follows:


Direct application by immersion: Immerse the piece directly in alcohol, so that the entire surface comes into contact. Remove the piece and then, and let it drain so that the alcohol can evaporate freely. It must be taken into account that this method is very aggressive, and if the alcohol penetrates too much into the piece, it can soften by varying the geometry.


Evaporative application: In a closed container, insert a paper soaked in alcohol placed so that it is around the piece. Then we introduce the piece taking great care that they do not come into contact. Close the container and allow evaporation to affect the piece, achieving the desired effect.


2. LEAVE THE PART AT REST


Leave the piece to rest inside the container. Once the piece has been impregnated in alcohol, let it dry in the air, depending on the amount of alcohol absorbed by the piece it can soften a little, when the alcohol has completely evaporated the piece will return to its normal state.


Following the previous steps, we managed to dissolve the surface layer of the piece, achieving a perfect union between layers and forming a continuous solid, which allows the material to acquire its transparency.


HOW TO POLISH A PIECE


To smooth the surface of the part, the previous process can be applied to parts with any geometry. In this case, care must be taken when immersing in alcohol because it can get inside the filling of the piece, affecting the material too much and compromising its integrity.


  1. Print the piece using Glace.
  2. Apply the alcohol treatment (ethyl or isopropyl) by the following methods:
  3. Direct application by immersion.
  4. Direct application by tools. (sprayed, applied with a brush, etc.)
  5. Evaporative application
  6. Leave the piece to rest so that the alcohol evaporates, an excess of alcohol can soften too much material.
Print Settings (As reference)
Printing temperature205ºC - 235ºC
Heated BedRecommended
Layer FanOptional
MaterialGLACE

0% Customers recommend this product

  • 5 Awesome
    0%
  • 4 Great
    0%
  • 3 Average
    0%
  • 2 Bad
    0%
  • 1 Poor
    0%
Please login or register to review

Reviews Over SMARTFIL GLACE 1.75mm - Transparent Filament - Smart Materials 3D

  • (0)

Total Reviews (0)
click here write review to add review for this product.