Menu
Your Cart

Search

Search Criteria

Products meeting the search criteria

Mega 2560 R3 (Compatible)
-29 % Out of Stock
Stock: Out of Stock Model: MegaCompatible
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 .It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a rese..
17.99€ 12.75€ Ex Tax:10.54€
Mega 2560 R3 (Compatible) 16u2
Recommended -38 % Out of Stock
Stock: Out of Stock Model: Mega 2560 R3 (Compatible) 16u2
Mega 2560 R3 (Compatible) 16u2This is a clone of quality, not only just aesthetically , also uses the same chip USB connection so it is 100 % compatible with the original drivers.It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ..
24.99€ 15.45€ Ex Tax:12.77€
Stock: In Stock Model: 3MOS-MKS
MKS 3MOS is a connection fan module. The module integrates 3 MOS control outputs, and its pins and dimensions are compatible with pluggable motor drive slots. It can be used directly by connecting to the drive slot and simply configuring the pin file. Suitable for motherboards with more than 5 axis ..
2.70€ Ex Tax:2.23€
Stock: In Stock Model: Eagle-MKS
MKS Eagle is an integrated version of Nano V3.0. Features:Cortex-M4 with FPU 32-bit, 168 MHz. Flash: 512 KB. RAM: 192KB.Compatible with UBS disk printing and TF card printing.Supports Virtual USB Device function.Integrated 5 TMC2209 driver with UART mode.Integrated snap-on drive heat sink and a..
52.50€ Ex Tax:43.39€
Stock: In Stock Model: Monster8-V2-MKS
MKS Monster8 V2 is an upgraded version of Monster8 V1. On the basis of retaining the functions of the original V1, has added independent DV5V for the Raspberry Pi, has reserved Robin WIFI interface for RRF firmware, added more protection circuits and reserved more functional interfaces.Specs:MCU: ST..
46.99€ Ex Tax:38.83€
Stock: In Stock Model: MKS-PI
Version: 1.1MKS PI is a high-end microcomputer board designed by Makerbase to replace the Raspberry Pi for the convenience of 3D printing users to use the Klipper firmware. The size, mounting holes, and most interface locations are also compatible with Raspberry Pi 3B. In terms of hardware, MKS PI h..
48.50€ Ex Tax:40.08€
Stock: In Stock Model: SKIPR
Version: 1.0MKS SKIPR is an all-in-one board launched by Makerbase for running Klipper. It integrates the RK3328 SOC running the Klipper host and the STM32F407VET6 MCU responsible for executing specific machine actions. It meets the use of most 3D printers.Features and advantages:SOC uses Rockchip's..
79.99€ Ex Tax:66.11€
Stock: In Stock Model: dual-axis-module
Simple complement to connect two motors in parallel, usually used with Z axis, but can be used with any other axis. Recommended to connect two equal motors so that the current is distributed equally between them.Use with small or medium sized 3D printers, avoid large sized motors.Content:1x Boa..
1.25€ Ex Tax:1.03€
Module mosfet 0-24v IRF520 - Arduino compatible Module mosfet 0-24v IRF520 - Arduino compatible
Out of Stock
Stock: Out of Stock Model: mosfet-module
It can control the current of devices or accessories, such as fans, or additional lights.Signal Voltage: 3.3V, 5VOutput voltage: 0-24 VRated current: <5A (To overcome 1A it needs additional dissipation)Size: 33 x 25mm 1 Piece..
1.75€ Ex Tax:1.45€
Stock: In Stock Model: Portable-Input-Shaper
With the Portable Input Shaper, the resonance of the axes can be measured by different axes to be later compensated by the printers.Features:Based on the popular RP2040 chip.Portable, you can use it on multiple 3D printers with Klipper firmware with the same configuration file.Small in size and easy..
14.99€ Ex Tax:12.39€
Stock: In Stock Model: CajaRamps-3DSteel
Printed part for the electronics that the 3DSteel printer carries. Protects and assembles in the structure in an easy and safe way.All the electronic components remain inside and have space to lodge in an orderly manner the excess cable in case of needed.Material: PLA 3D850.You can optionally add th..
7.50€ 6.00€ Ex Tax:4.96€
Stock: In Stock Model: Caja-Electronica-3DSteel-V2
Printed part for the electronics that the 3DSteel V2 printer carries. Protects and assembles in the structure in an easy and safe way.All the electronic components remain inside and have space to lodge in an orderly manner the excess cable in case of needed.Material: PLA 3D850.You can optionally add..
7.50€ 6.00€ Ex Tax:4.96€
Showing 25 to 36 of 58 (5 Pages)