Spider Board is a small but powerful 3D printer control board. In a limited space, it integrates 8 stepper motor drives, 5A 12V power supply, 8A 5V power supply, which provides powerful energy for fans of various voltages, various RGB light strips and Raspberry Pi. You can build a 3D printer with ri..
Spider Board is a small but powerful 3D printer control board. In a limited space, it integrates 8 stepper motor drives, 5A 12V power supply, 8A 5V power supply, which provides powerful energy for fans of various voltages, various RGB light strips and Raspberry Pi. You can build a 3D printer with ri..
Based on two legends: the Klicky Probe by JosAr and the Euclid Probe. With D2HW-A201D PCB.This design attempts to replicate Klicky as closely as possible using a PCB-based design, to try and achieve the following aims:Reduce the problem of magnets working lose or seating poorly in printed parts.Incr..
FYSETC Metal Sherpa V1.5 CNC Extruder.Features:Compact size Sherpa extruder designed for use with any printer, with dual gear filament gripping system.Made of aviation aluminum, which gives it resistance to high temperatures. In addition, compact and lightweight design.CNC POM Gear: Reduction engrav..
Logic:Compatible with accessories for Arduino MEGA. Atmega2560 and Atmega32u2 processors are compatible with all RAMPS type firmware.Crystals for USB and processor (sync time at 10ppm).3 thermistor taps + 4th thermistor circuit for ZProbe.Motor controllers:4 Trinamic TMC2130 motor drivers up to 1/25..
Current Version: V2Designed for a single extruder 3D printer. Many interfaces are reserved for features such as AC detection, filament detection, leveling with 3Dtouch or other sensors.Features:Compact size: 101.5mm x 72mm. Compatible with the Creatlity Ender 3 motherboard sizeFully integrated all i..
Features:Rated voltage: 24VIncludes strong neodymium magnets that do not lose properties up to 140ºC4 fixing holes for countersunk screwsPre-welded power cablesThermistor included with connectorFast and uniform heatingNominal resistance: 1.6 ohmsNominal power 360WMounting hole spacing: 240mm for M4 ..
With the Portable Input Shaper, the resonance of the axes can be measured by different axes to be later compensated by the printers.Features:Based on the popular RP2040 chip.Portable, you can use it on multiple 3D printers with Klipper firmware with the same configuration file.Small in size and easy..
R4 Board designed to be used in Voron 0 3D printers.Characteristics:Small and compact board, size 86x48mmFour layer PCB.Trabaja con Raspberry PI Arm Cortex-M0.MCU RP2040.Fuse easy to remove in case you need to change it.Communication type C.Works at 12 or 24 V.Logic voltage: 3.3 V.Controller: TMC220..
Actual Version: 2.1The S6 board is based on the STM32F446 32bit mcu has six drive sockets and supports the full range of TMC drives. They have fully extended the resources of the MCU so that you can maximize its power. They considered the possible use scenarios of 3D printers and designed a series o..
FYSETC Sherpa V1.5 extruder.Small size Sherpa extruder, dual gear filament gripping system designed for use with any printer.It features a 6.25:1 gear-driven design to provide torque with near-silent operation. For best results it is recommended to adjust it for your printer.Using an SLS printed she..
The Stealthburner CAN Tool Board is a highly integrated printhead control board. Based on STM32F072, running Klipper firmware. Onboard TMC2209 stepper motor driver, AXL345 acceleration sensor, and other necessary interfaces. And comes with a 2.5m 4-core cable for easy out-of-the-box use.Features:Bas..