-8 %
Stock: In Stock
Model: Relé 10A Omron
Omron G3NB-210B-1 solid-state relay for controlling AC loads from a 5 to 24 V DC signal. Its 24 to 220 V AC output is particularly suitable for resistive heaters, automation and properly protected mains-powered heated beds.
Main specifications
ReferenceOmron G3NB-21..
15.00€ 13.75€
Ex Tax:11.36€
Stock: In Stock
Model: Orbiter-V2.5-upgrade
This Orbiter V2.5 upgrade kit updates the transmission of an existing Orbiter V2.0 extruder without replacing the full assembly. It adds the revised drive-gear geometry, a pre-assembled spider shaft, planetary gears and moulded gear housing.
Important: this is a mechanical upgrade kit, not a comple..
35.99€
Ex Tax:29.74€
Stock: In Stock
Model: LCD-Cable-1m
A pack of two 1 m flat ribbon cables with ten conductors and 2 × 5 female IDC connectors. It is intended for RepRap LCD displays that need simultaneous EXP1 and EXP2 connections to a compatible controller or adapter.
The one-metre length makes it easier to mount a display away from the electronic..
1.85€
Ex Tax:1.53€
-30 %
Stock: In Stock
Model: Eje-Y-3DSteel-V2
A set of PETG printed parts for building or repairing the HTA3D 3DSteel V2 Y axis. It includes the linear-bearing holders, motor-mount spacers and belt anchor used by the original design.
This is a machine-specific mechanical subset rather than a universal kit for every P3Steel or Prusa i3 Steel...
5.00€ 3.50€
Ex Tax:2.89€
-20 %
Stock: In Stock
Model: CajaRamps-3DSteel
Printed enclosure designed to install and protect the RAMPS 1.4-based electronics used by the HTA3D 3DSteel 3D printer.
Its geometry allows it to be attached to the machine frame, keeps the electronic components protected and provides room for organising surplus wiring. It is printed in PLA.
..
7.50€ 6.00€
Ex Tax:4.96€
-20 %
Stock: In Stock
Model: Caja-Electronica-3DSteel-V2
Printed enclosure designed to install and protect the BIGTREETECH SKR V1.4 board used by the HTA3D 3DSteel V2 3D printer.
It attaches to the machine frame and helps keep the electronics protected and the wiring organised. It is printed in PLA, with geometry designed for the SKR 1.4 installation u..
7.50€ 6.00€
Ex Tax:4.96€
Stock: In Stock
Model: Alicate-corte
The PLATO 170 Platoshear is a compact flush-cutting tool designed for precision electronics and assembly work. Its thin blade profile provides access to confined areas and makes it particularly useful for cutting 3D printing filament, electronic component leads and soft copper wire.
It uses a she..
2.50€
Ex Tax:2.07€
-20 %
Stock: In Stock
Model: Protector-fuente-3Dsteel
Printed-part set designed to protect the power-supply connections used on the original HTA3D 3DSteel. It consists of a base and a ventilated cover that provide access during installation while reducing accidental exposure to the terminals.
The cover is prepared for a switched IEC mains inlet, all..
7.50€ 6.00€
Ex Tax:4.96€
Stock: In Stock
Model: Aislante-Hotend
This rock wool insulation is designed to wrap the hotend heater block, reducing heat loss during printing. Its low thermal conductivity helps maintain a more stable temperature while improving heating efficiency.
Features
Reduces heat loss from the heater block.
Helps maintain a sta..
0.19€
Ex Tax:0.16€
Stock: In Stock
Model: PieGoma
Black rubber foot for supporting 3D printers, small machines and structures. Its elastic body helps reduce rigid contact with the supporting table and may decrease the transmission of certain vibrations and structure-borne noise.
It has an M6 internal thread for attachment to the machine base. Th..
0.75€
Ex Tax:0.62€
Stock: In Stock
Model: Schuko-1m
This power cable connects equipment with an IEC 60320 C13 connector to a standard Schuko (CEE 7) mains outlet. It is commonly used with desktop computers, 3D printers, monitors, power supplies, servers and other compatible electronic devices.
The three-conductor design provides live, neutral and ..
2.35€
Ex Tax:1.94€
Out of Stock
Stock: Out of Stock
Model: Nevermore Mix 50%-50%
This package is composed of 50% Activated Carbon and 50% Scorch.Nevermore Scorch is an advanced air filtration media, designed for the unique demands of 3D printer chambers, especially at elevated temperatures. Traditional carbon filters become less effective above 50°C and are significantly less ef..
24.00€
Ex Tax:19.83€