Stock: In Stock
Model: Termistor100K ohm NTC 3950 cableado
100K NTC Beta 3950 thermistor for temperature measurement in hotends, heated beds and other compatible thermal control systems. It is supplied pre-wired with a 1 metre cable and a Dupont connector, making it suitable for replacement and new FDM 3D printer installations.
Features
Sensor type: NTC..
0.65€
Ex Tax:0.54€
Stock: In Stock
Model: Termistor100K ohm NTC 3950 cableado-XH
Pre-wired 100K NTC Beta 3950 thermistor for temperature measurement in compatible hotends, heated beds and thermal control projects. It includes a 1 metre cable and a 2-pin XH connector.
Features
Type: NTC thermistor.
Nominal resistance: 100K at 25 °C.
Beta value: 3950.
Cable length: 1 m.
Co..
0.65€
Ex Tax:0.54€
Stock: In Stock
Model: Cable-16AWG-50cm-01
Pair of flexible 16 AWG wires, one red and one black, prepared for connecting a heated bed to a 3D printer controller board. Each conductor is approximately 50cm long and has a pre-insulated pin terminal fitted to one end for connection to a compatible terminal block.
The wires use stranded tinne..
2.25€
Ex Tax:1.86€
-23 %
Stock: In Stock
Model: 3DLAC
3DLAC is a Spanish-made aerosol adhesive designed to improve first-layer adhesion to the printing surface. It helps reduce corner lifting and warping when printing materials such as PLA, ABS, PETG, Nylon and TPU, provided that the bed, temperature and first-layer settings are correctly adjusted.
..
7.50€ 5.80€
Ex Tax:4.79€
-14 %
Stock: In Stock
Model: 3DLAC Plus
3DLAC Plus is a concentrated adhesive designed to improve first-layer adhesion in 3D printing. Its 100ml spray-bottle format provides controlled application without using a pressurised aerosol.
It is particularly intended for demanding materials and prints requiring stronger adhesion, including A..
6.50€ 5.60€
Ex Tax:4.63€
Stock: In Stock
Model: 3DLAC Stick
3DLAC Stick 80 ml is a 3D printer build-plate adhesive with a sponge applicator. It makes it easy to spread a thin coating only where the model will be printed, without aerosol overspray and with particularly convenient control for small or localised prints.
Its water-based, alcohol-free formula ..
4.35€
Ex Tax:3.60€
Only a few units in stock
-7 %
Stock: In Stock
Model: 3DNylon
3DNYLON 30 ml is a brush-on adhesive specifically developed to improve the first layer when printing nylon or polyamide (PA) filaments. It helps keep the part attached to the bed and reduce corner lifting, a common challenge with this material.
The applicator makes it possible to spread a thin, eve..
21.00€ 19.50€
Ex Tax:16.12€
Out of Stock
Stock: Out of Stock
Model: Clip-cristal
Black metal clip with a knurled adjustment screw for securing glass and other removable rigid build surfaces to a 3D printer heated bed.
The U-shaped body fits over the edge of the bed, while the screw allows the clamping pressure to be adjusted. Its compact design occupies little space on the bu..
3.75€
Ex Tax:3.10€
-32 %
Stock: In Stock
Model: Dimafix
DIMAFIX Adhesive Spray for 3D Printer Heated Beds — 400 ml
DIMAFIX is an adhesive spray for improving first-layer adhesion on FFF/FDM 3D printers with heated beds. It is especially useful when a print needs additional protection against lifting or warping during printing.
Adhesion activates when t..
18.99€ 12.85€
Ex Tax:10.62€
New
Stock: In Stock
Model: Dimafix-pen
DIMAFIX Pen Heated-Bed Adhesive for 3D Printing — 90 ml
Liquid DIMAFIX adhesive in an applicator-pen format for improving first-layer adhesion on FFF/FDM 3D printers with heated beds. The pen format allows precise, local application to the print area.
Its adhesive effect activates at approximately..
13.25€
Ex Tax:10.95€
Stock: In Stock
Model: Mosfet-30A-Fysetc
External MOSFET power stage with a large heatsink for controlling heated beds, heaters and other resistive DC loads in 3D printers and similar machines.
The module allows the controller board to continue regulating temperature while the main heated-bed current is supplied directly by the power su..
13.25€
Ex Tax:10.95€
Stock: In Stock
Model: CamaCaliente-sujecion
Hardware kit for mounting and levelling a 3D-printer heated bed with four countersunk holes. It includes M3 screws, compression springs, wide washers and self-locking nuts to create four adjustable mounting points.
The springs allow the distance between the heated bed and Y carriage to be adjuste..
1.50€
Ex Tax:1.24€