Stock: In Stock
Model: Termistor100K-PT100-3mm-XH
100K NTC Beta 3950 hotend thermistor with a 3 mm cylindrical 304 stainless-steel capsule, 1 metre cable and XH connector. Its encapsulated construction provides a robust fit in heater blocks designed for cylindrical temperature sensors.
Features
100K NTC Beta 3950 thermistor.
304 stainless-stee..
0.85€
Ex Tax:0.70€
Stock: In Stock
Model: BTT Mini 12864 LCD
The BIGTREETECH MINI12864 V2.0 is a compact 128 × 64 graphic display for controlling compatible 3D printers and other machines directly through a rotary encoder. It integrates a full-size SD card reader, clickable encoder, reset button, beeper and three addressable RGB LEDs for the backlight.
Thi..
11.99€
Ex Tax:9.91€
Stock: In Stock
Model: SFS V2.0-1.75
The BIGTREETECH Smart Filament Sensor SFS V2.0 combines two monitoring systems for 1.75 mm filament: a switch that detects its presence and a photoelectric encoder that checks whether the material is moving during extrusion.
This combination can detect both filament runout and incidents that stop..
15.99€
Ex Tax:13.21€
Stock: In Stock
Model: TMC2209-Bigtreetech
The BIGTREETECH TMC2209 V1.3 is a StepStick driver for two-phase bipolar stepper motors, designed for quiet motion, accurate control and advanced configuration in 3D printers, light CNC machines, robots and automation projects. It can operate through standard STEP/DIR signals or communicate over UAR..
4.75€
Ex Tax:3.93€
Stock: In Stock
Model: 12025-Hydraulic-24V
GDSTIME 12025 24V axial fan measuring 120 × 120 × 25 mm and equipped with a hydraulic bearing. It provides large-format ventilation with a balance focused on reducing noise and electrical consumption.
Its nominal speed of 2000 RPM and stated airflow of 77 CFM make it suitable for electronics encl..
3.50€
Ex Tax:2.89€
Stock: In Stock
Model: 3010Blower-Ballbearing-24V
GDSTIME 3010 24V centrifugal blower fan with dual ball bearings and a 15 cm cable. Its compact 30 × 30 × 10 mm format provides directed airflow in installations where very little space is available.
The dual ball bearing system is particularly suitable for applications involving long operating pe..
6.75€
Ex Tax:5.58€
Stock: In Stock
Model: 5015Blower-BallBearing-24V-1m
GDSTIME 5015 24V centrifugal blower fan with dual ball bearings, a 2-pin XH2.54 connector and a 1 metre cable. Its 50 × 50 × 15 mm format is widely used for part cooling in 3D printers and other applications requiring concentrated airflow.
The dual ball bearing system is particularly suitable for..
5.99€
Ex Tax:4.95€
-17 %
Stock: In Stock
Model: 6010-5V
GDSTIME 6010 5V axial fan with an 11-blade impeller, a 2-pin XH2.54 connector and an approximately 20 to 25 cm cable. Its 60 × 60 × 10 mm format provides direct cooling while maintaining a slim profile.
It is suitable for electronic boards, single-board computers, small enclosures and other 5V de..
5.45€ 4.50€
Ex Tax:3.72€
Stock: In Stock
Model: TMC2209-MKS
The MKS TMC2209 V2.0 is a StepStick driver for two-phase bipolar stepper motors, designed to reduce motion noise and allow advanced firmware configuration. It can operate through conventional STEP/DIR signals or use single-wire UART to configure current, microsteps, operating modes and diagnostics.
..
4.99€
Ex Tax:4.12€
Stock: In Stock
Model: 17HS4401s-T8x8-350MM
NEMA 17 17HS4401S bipolar stepper motor with an integrated 350 mm TR8×8 trapezoidal lead screw. It is intended for direct linear motion in Z axes, actuators and DIY machines without a coupling between the motor and the lead screw.
The lead screw forms part of the motor shaft, simplifying the asse..
25.00€
Ex Tax:20.66€
Stock: In Stock
Model: 17HS8401
The 17HS8401 is a bipolar NEMA 17 stepper motor with a long 42 × 48mm body, a 1.8° step angle and a minimum 52N·cm holding torque. It is intended for axes and mechanisms requiring more torque margin than a 40mm-long NEMA 17 while retaining the standard 42mm front interface.
Its front 5mm D-shaped..
12.25€
Ex Tax:10.12€
New
Stock: In Stock
Model: MELLOW-SEXBOLT-Z
The Mellow Hartk Sexbolt is a Z-endstop assembly for Voron 2.4 and Trident printers that use a fixed nozzle-actuated pin to establish their height reference. It combines the moulded housing, microswitch PCB and pin guide in a compact unit, avoiding the need to source and assemble the housing and end..
12.95€
Ex Tax:10.70€