-25 %
Stock: In Stock
Model: 4020-BallBearing-Fan-24V-1m
4020 24V axial fan with a ball bearing system and a 1 metre power cable. Its 40 × 40 × 20 mm format is suitable for cooling heatsinks, electronics and compact equipment that can accommodate a 20 mm thick housing.
The ball bearing system is intended for frequent or extended operation, particularly..
4.80€ 3.60€
Ex Tax:2.98€
-71 %
Stock: In Stock
Model: 6010-24V
6010 24V axial fan with an 11-blade impeller, a 2-pin XH2.54 connector and an approximately 20 cm cable. Its nominal 60 × 60 × 10 mm dimensions provide broad airflow while maintaining a slim profile.
It is suitable for cooling electronics, controller boards, power supplies and small enclosures us..
5.45€ 1.59€
Ex Tax:1.31€
-68 %
Stock: In Stock
Model: 6015-24v
6015 24V axial fan with a 7-blade impeller, a 2-pin XH2.54 connector and an approximately 20 cm cable. Its 60 × 60 × 15 mm dimensions provide an intermediate format between 6010 and 6020 fans.
It can be used to cool electronic boards, power supplies, controllers and compartments requiring air cir..
5.99€ 1.89€
Ex Tax:1.56€
-28 %
Stock: In Stock
Model: 6015-BallBearing-Fan-24V
6015 24V axial fan with a ball bearing system and a 15 cm cable. Its nominal 60 × 60 × 15 mm dimensions make it suitable for cooling electronics, power supplies and enclosures used in 3D printers or CNC machines.
The ball bearing system is particularly suitable for equipment subject to extended o..
4.50€ 3.25€
Ex Tax:2.69€
Out of Stock
Stock: Out of Stock
Model: CadenaPortacables7x7
Nylon cable drag chain for guiding and protecting flexible wiring during repeated movement in 3D printers, CNC machines, robots and automation equipment. This compact version has a nominal internal cross-section of 7 × 7mm and an approximate length of 1 metre.
Its small size is suitable for insta..
3.25€
Ex Tax:2.69€
Stock: In Stock
Model: Spiral-1m
This 8 mm spiral cable wrap is designed to bundle and protect cables quickly and neatly. Its flexible spiral design allows cables to be added or removed at any point without dismantling the entire cable bundle.
Features
Flexible spiral cable wrap.
8 mm nominal diameter.
Protect..
0.39€
Ex Tax:0.32€
Stock: In Stock
Model: A4988
The A4988 Pololu-compatible driver is one of the most widely used stepper motor drivers for 3D printers, CNC machines and automation projects. It controls bipolar stepper motors using STEP/DIR signals and supports multiple microstepping modes for smooth and precise motion.
Features
Drive..
1.79€
Ex Tax:1.48€
-67 %
Out of Stock
Stock: Out of Stock
Model: UNO R3-au16
Arduino UNO R3 compatible development board based on a 16 MHz 8-bit ATmega328P-AU microcontroller and fitted with a CH340G USB-to-serial converter.
It retains the 5 V logic, pin arrangement and form factor of the UNO R3 platform, making it suitable for learning, prototyping, sensors, simple autom..
19.00€ 6.35€
Ex Tax:5.25€
Stock: In Stock
Model: ADXL345 V2.0
The BIGTREETECH ADXL345 V2.0 is a USB accelerometer designed to measure a 3D printer's resonances and help calibrate Input Shaper in Klipper. It combines an ADXL345 sensor with its own RP2040 microcontroller, allowing it to connect to the Klipper host over USB-C without routing SPI signals to the ma..
11.35€
Ex Tax:9.38€
-14 %
Out of Stock
Stock: Out of Stock
Model: BTT02-V1.0
The BIGTREETECH BTT002 V1.0 is a 32-bit controller board developed as a configurable alternative to the Einsy Rambo used by the Original Prusa i3 MK3S. It features a 168 MHz STM32F407VGT6 microcontroller, runs from 12 or 24 V and uses replaceable StepStick drivers instead of soldered motor drivers.
..
69.99€ 59.99€
Ex Tax:49.58€
Only a few units in stock
-18 %
Stock: In Stock
Model: BTT-CB1
The BIGTREETECH CB1 V2.2 with 1 GB RAM is a compact computer module designed to run Linux and act as a host for Klipper, Moonraker and Mainsail on compatible carrier boards. It combines a quad-core 1.5 GHz Allwinner H616 Cortex-A53 processor with 2.4 GHz Wi-Fi and provides the signals required for a..
36.75€ 29.99€
Ex Tax:24.79€
Out of Stock
Stock: Out of Stock
Model: BTT-CB2
The BIGTREETECH CB2 V1.0 is a computer module for running Linux and Klipper on a compatible carrier board such as a Manta. It has a quad-core Rockchip RK3566, 2 GB of LPDDR4 RAM, 32 GB of onboard eMMC storage and 2.4/5 GHz Wi-Fi. Its mounting format and two underside connectors follow the Raspberry ..
53.50€
Ex Tax:44.21€