-68 %
Stock: In Stock
Model: 6015-24v
Fan Specifications 6015Size: 60x15mm 7 Blades Connector: XH2.54-2P Nominal current: 0.16 ± 10% Amp Rated Voltage: DC24V Ruido: 18dba±10% Fan speed: 2600±10% RPM Air flow: 21.5CFM Weight: 35 g/pcs Cable lenght: 20 cm 1 Piece ..
5.99€ 1.89€
Ex Tax:1.56€
-28 %
Stock: In Stock
Model: 6020-RodBolas-24V
Fan Specifications 6020Size: 60x60x20mm Connector: XH2.54-2P Ball bearingNominal current: 0.1A ± 10%Rated Voltage: 24V Power: 1.7WRuido: 35.8dba±10% Fan speed: 5000 RPM Air flow: 28.05CFM Life: 50000 hoursWeight: 48gCable lenght: 25 cm 1 Piece ..
8.50€ 6.10€
Ex Tax:5.04€
Stock: In Stock
Model: 6020Hidralico-24V
Fan Specifications 6020Size: 60x60x20mm Connector: XH2.54-2P HydraulicNominal current: 0.1 ± 10% Amp Rated Voltage: 24V Power: 1.7WRuido: 34.3dba±10% Fan speed: 4500 RPM Air flow: 26.2CFM Weight: 48gCable lenght: 25 cm 1 Piece ..
4.10€
Ex Tax:3.39€
Stock: In Stock
Model: A4988
It is one of the most popular stepper motor controllers, its high performance and low cost makes it ideal for any 3D printer or CNC that use currents lower than 2A.Characteristics: Low resistance Short circuit and overheat protections Rated current 2A Step modes: 1/16, 1/8, 1/4, ..
1.79€
Ex Tax:1.48€
New
Out of Stock
Stock: Out of Stock
Model: ADXL345 V2.0
Version: 2.0BIGTREETECH ADXL345 V2.0 is a module for 3D printer resonance compensation. It can communicate through USB, greatly simplifying wiring.Main features:The board has a reserved BOOT button for easey firmware updates.Reserved solder points enable users to customize wiring easily.The USB port..
11.35€
Ex Tax:9.38€
Stock: In Stock
Model: KlickyProbe-Fysetc
Based on two legends: the Klicky Probe by JosAr and the Euclid Probe. With D2HW-A201D PCB.This design attempts to replicate Klicky as closely as possible using a PCB-based design, to try and achieve the following aims:Reduce the problem of magnets working lose or seating poorly in printed parts.Incr..
17.50€
Ex Tax:14.46€
Stock: In Stock
Model: E3-RRF
E3 RRF Board.Features:High performance main control chip:Packs ARM Cortex-M4 STM32F407VGT6 chip with its main frequency up to 168MHz.Power chip:Adopts AO1284 power chip with the power input of DC 12/24V and maximym output curent up to 4A, greatly reducing power ripple and radiation interference,Inte..
69.99€
Ex Tax:57.84€
Stock: In Stock
Model: Cable Bipolar - 1mm2
The price is for 1 meter, if you want consecutive meters we can offer up to 10 meters...
0.59€
Ex Tax:0.49€
Stock: In Stock
Model: BTT-CB1
Version: 2.2CB1 outputs signals to the motherboard through the micro BTB two-pin connection, including 100M Ethernet, HDMI, etc. Also, built-in 2.4G Wi-Fi. With its powerful 64-bit ARM Quad Core processor and 1 GB of DDR3 RAM, it has enough power to run Klipper, Linux or Debian.Compatible with Manta..
36.75€
Ex Tax:30.37€
New
Stock: In Stock
Model: BTT Micro Probe
Main features:Ultra small, fits into more places.Lighteweight desing.Easy installation.Compatible with wide range of FDM printers.High precision and reliability.Specifications:Name: MicroProbe.Total weight: 6g.Voltage: 5V.Standard-By current: 19mA.Operating Current: 350mA.Cable Length: 1.5m.Wiring: ..
24.99€
Ex Tax:20.65€
New
Out of Stock
Stock: Out of Stock
Model: BTT-Pi
Version: 1.2Features:Strategic Partnership KLIPPER and BIGTREETECH - The cooperation between KLIPPER and BIGTREETECH makes firmware for 3D printing enthusiasts more convenient to use and helps to further enhance the printing experience.Efficient and Powerful - 64-bit Quad-Core Architecture │ ARM®Cor..
34.99€
Ex Tax:28.92€
Only a few units in stock
-14 %
Stock: In Stock
Model: BTT02-V1.0
The BTT02 V1.0 board is a versatile board, which can be used as a replacement for the Prusa I3 MK3S printer board (Einsy Rambo board).Specifications:Microprocessor: 168MHz ARM Cortex-M4 CPU with STM32F407VGT6 chipVoltage: 12 / 24VLogic voltage: 3.3VMotor Drivers: 5 (including double Z)Engines: XM, Y..
69.99€ 59.99€
Ex Tax:49.58€