Out of Stock
Stock: Out of Stock
Model: GT2-POWGE-RF-belt-9mm
POWGE RF 9 mm GT2 timing belt, manufactured from nylon-covered neoprene and reinforced with internal fiberglass cords.
Its increased width provides a larger tooth contact area than a 6 mm belt, provided that the pulleys, idlers and fastening points are designed for a 9 mm belt. The RF range is in..
6.85€
Ex Tax:5.66€
-20 %
Stock: In Stock
Model: Protector-fuente-3Dsteel
Printed-part set designed to protect the power-supply connections used on the original HTA3D 3DSteel. It consists of a base and a ventilated cover that provide access during installation while reducing accidental exposure to the terminals.
The cover is prepared for a switched IEC mains inlet, all..
7.50€ 6.00€
Ex Tax:4.96€
-40 %
Stock: In Stock
Model: Prusa i3 Rework-Tornillería
Fastener kit for assembling or repairing a Prusa i3 Rework with the classic mechanical configuration based on M10 threaded rods and M5-thread Z-axis motion. It brings together screws, nuts, washers, bed springs and the special hardware used by the extruder and Z axis.
It is a practical way to obtai..
20.00€ 12.00€
Ex Tax:9.92€
-34 %
Stock: In Stock
Model: Prusai3-Rework
This kit includes the printed parts required to assemble, repair or upgrade a Prusa i3 Rework 3D printer. All parts are designed to maintain compatibility with this printer model while incorporating several improvements over the original design to simplify assembly and enhance overall performance.
..
32.00€ 21.00€
Ex Tax:17.36€
Stock: In Stock
Model: PTC-12V-120W
The PTC Heater (Positive Temperature Coefficient) is the ideal solution for those seeking an efficient, safe, and long-lasting heating system. Ideal for heated 3D printers.Designed with advanced technology and high-quality materials, this device stands out for its exceptional performance and ease of..
14.99€
Ex Tax:12.39€
Only a few units in stock
-13 %
Stock: In Stock
Model: PTC-12V-70W
The PTC Heater (Positive Temperature Coefficient) is the ideal solution for those seeking an efficient, safe, and long-lasting heating system. Ideal for heated 3D printers.Designed with advanced technology and high-quality materials, this device stands out for its exceptional performance and ease of..
14.99€ 12.99€
Ex Tax:10.74€
Stock: In Stock
Model: PTC-220V-100W
The PTC Heater (Positive Temperature Coefficient) is the ideal solution for those seeking an efficient, safe, and long-lasting heating system. Ideal for heated 3D printers.Designed with advanced technology and high-quality materials, this device stands out for its exceptional performance and ease of..
18.99€
Ex Tax:15.69€
Out of Stock
Stock: Out of Stock
Model: PTC-220V-200W
The PTC Heater (Positive Temperature Coefficient) is the ideal solution for those seeking an efficient, safe, and long-lasting heating system. Ideal for heated 3D printers.Designed with advanced technology and high-quality materials, this device stands out for its exceptional performance and ease of..
14.99€
Ex Tax:12.39€
Stock: In Stock
Model: PTC-24V-200W
The PTC Heater (Positive Temperature Coefficient) is the ideal solution for those seeking an efficient, safe, and long-lasting heating system. Ideal for heated 3D printers.Designed with advanced technology and high-quality materials, this device stands out for its exceptional performance and ease of..
14.99€
Ex Tax:12.39€
Stock: In Stock
Model: Teflon-tube-4/2.5-1m
This PTFE guide tube has a 4 mm outer diameter and a 2.5 mm inner diameter. It is suitable for guiding 1.75 mm filament in 3D printers, Bowden extrusion systems and auxiliary paths between the spool, a dry box and the extruder.
Its inner diameter provides more clearance than a conventional 4 × 2 ..
1.02€
Ex Tax:0.84€
Stock: In Stock
Model: Teflon-tube-4/3-1m
This PTFE guide tube has nominal dimensions of 4 mm outer diameter and 3 mm inner diameter. Its wide internal passage makes it suitable as a low-restriction filament guide, particularly between a spool or dry box and the extruder.
It can be used with 1.75 mm filament when a generous clearance is ..
0.80€
Ex Tax:0.66€
Stock: In Stock
Model: Teflon-tube-6/4-1m
This PTFE tube with a 6 mm outer diameter and 4 mm inner diameter is designed for Bowden extrusion systems using 3.00 mm filament. Its low-friction surface promotes smooth filament movement and reliable material feeding.
Features
Manufactured from low-friction PTFE.
Compatible with ..
2.20€
Ex Tax:1.82€