Stock: In Stock
Model: POWGE-GT2-20T-NoTeeth-10mm-di5
POWGE smooth idler pulley with an integrated bearing and a nominal 20T-equivalent size, designed to guide or tension the back of a GT2 belt up to 10 mm wide on a nominal 5 mm axle or screw.
Its smooth cylindrical running surface supports the back of the belt without engaging its teeth. The side f..
3.55€
Ex Tax:2.93€
Out of Stock
Stock: Out of Stock
Model: GT2-POWGE-RF-belt-10mm
POWGE RF 10 mm GT2 timing belt, manufactured from nylon-covered neoprene and internally reinforced with fiberglass.
This width is intended for transmissions designed with pulleys, idlers and fastening points for 10 mm GT2 belts. The RF range is intended to reduce vibration, friction and dust gene..
6.99€
Ex Tax:5.78€
Out of Stock
Stock: Out of Stock
Model: GT2-POWGE-RF-belt-6mm
POWGE RF 6 mm GT2 timing belt, manufactured from nylon-covered neoprene and internally reinforced with fiberglass cords.
The RF range is intended for synchronous transmissions where reduced vibration, friction and dust generation are preferred compared with a conventional POWGE belt. Actual perfo..
4.99€
Ex Tax:4.12€
Out of Stock
Stock: Out of Stock
Model: GT2-POWGE-RF-belt-9mm
POWGE RF 9 mm GT2 timing belt, manufactured from nylon-covered neoprene and reinforced with internal fiberglass cords.
Its increased width provides a larger tooth contact area than a 6 mm belt, provided that the pulleys, idlers and fastening points are designed for a 9 mm belt. The RF range is in..
6.85€
Ex Tax:5.66€
-20 %
Stock: In Stock
Model: Protector-fuente-3Dsteel
Printed-part set designed to protect the power-supply connections used on the original HTA3D 3DSteel. It consists of a base and a ventilated cover that provide access during installation while reducing accidental exposure to the terminals.
The cover is prepared for a switched IEC mains inlet, all..
7.50€ 6.00€
Ex Tax:4.96€
-40 %
Stock: In Stock
Model: Prusa i3 Rework-Tornillería
Fastener kit for assembling or repairing a Prusa i3 Rework with the classic mechanical configuration based on M10 threaded rods and M5-thread Z-axis motion. It brings together screws, nuts, washers, bed springs and the special hardware used by the extruder and Z axis.
It is a practical way to obtai..
20.00€ 12.00€
Ex Tax:9.92€
-34 %
Stock: In Stock
Model: Prusai3-Rework
This kit includes the printed parts required to assemble, repair or upgrade a Prusa i3 Rework 3D printer. All parts are designed to maintain compatibility with this printer model while incorporating several improvements over the original design to simplify assembly and enhance overall performance.
..
32.00€ 21.00€
Ex Tax:17.36€
Stock: In Stock
Model: PTC-12V-120W
The PTC Heater (Positive Temperature Coefficient) is the ideal solution for those seeking an efficient, safe, and long-lasting heating system. Ideal for heated 3D printers.Designed with advanced technology and high-quality materials, this device stands out for its exceptional performance and ease of..
14.99€
Ex Tax:12.39€
Only a few units in stock
-13 %
Stock: In Stock
Model: PTC-12V-70W
The PTC Heater (Positive Temperature Coefficient) is the ideal solution for those seeking an efficient, safe, and long-lasting heating system. Ideal for heated 3D printers.Designed with advanced technology and high-quality materials, this device stands out for its exceptional performance and ease of..
14.99€ 12.99€
Ex Tax:10.74€
Stock: In Stock
Model: PTC-220V-100W
The PTC Heater (Positive Temperature Coefficient) is the ideal solution for those seeking an efficient, safe, and long-lasting heating system. Ideal for heated 3D printers.Designed with advanced technology and high-quality materials, this device stands out for its exceptional performance and ease of..
18.99€
Ex Tax:15.69€
Stock: In Stock
Model: PTC-220V-200W
The PTC Heater (Positive Temperature Coefficient) is the ideal solution for those seeking an efficient, safe, and long-lasting heating system. Ideal for heated 3D printers.Designed with advanced technology and high-quality materials, this device stands out for its exceptional performance and ease of..
14.99€
Ex Tax:12.39€
Out of Stock
Stock: Out of Stock
Model: PTC-220V-350W
The PTC Heater (Positive Temperature Coefficient) is the ideal solution for those seeking an efficient, safe, and long-lasting heating system. Ideal for heated 3D printers.Designed with advanced technology and high-quality materials, this device stands out for its exceptional performance and ease of..
14.99€
Ex Tax:12.39€