Stock: In Stock
Model: V6-fan-support
Fan mount and air duct designed to install a 30 × 30 × 10 mm 3010 axial fan on a V6-style hotend heatsink. The part clips around the side of the heatsink fins and directs the fan's airflow through them.
It is manufactured from black injection-moulded plastic. Its clip-on installation allows the f..
0.75€
Ex Tax:0.62€
Stock: In Stock
Model: Hermit-crab-V2
The BIGTREETECH Hermit Crab V2.0 CAN is a manual quick-change platform designed to keep several toolheads prepared and swap them without dismantling every carriage component. It includes one electronic fixed plate and three removable tool plates for compatible hotends, extruders, probes or other too..
158.50€
Ex Tax:130.99€
Stock: In Stock
Model: Teflón-4-2-negro
Black 2×4 mm PTFE tube for guiding 1.75 mm filament in 3D printers and Bowden systems. Its low-friction surface helps filament move when the machine uses fittings for 4 mm outside-diameter tubing.
It is supplied in 1 m per unit lengths. You can select several units to request a longer continuous se..
1.65€
Ex Tax:1.36€
Stock: In Stock
Model: Teflón-4-2-azul
Blue 2×4 mm PTFE tube for guiding 1.75 mm filament in 3D printers and Bowden systems. Its low-friction surface helps filament move between the feeder and hotend when the machine uses fittings for 4 mm outside-diameter tubing.
It is supplied in 1 m per unit lengths. You can select several units to..
1.65€
Ex Tax:1.36€
-60 %
Stock: In Stock
Model: Teflón-4-1.9-red
Red 1.9 × 4 mm PTFE Tube for 1.75 mm Filament
Red polytetrafluoroethylene (PTFE) tube with a 1.9 mm internal diameter and 4 mm external diameter. It is mainly intended to guide 1.75 mm filament in direct-drive extruders, where the smaller internal diameter helps guide the filament with limited clea..
6.00€ 2.40€
Ex Tax:1.98€
Stock: In Stock
Model: Calcetin-TZ-V6
This silicone sock for the TZ-V6 hotend wraps around the hot section to reduce heat loss, limit the direct effect of part-cooling airflow and help keep the block cleaner. It is a replacement part shaped specifically for the TZ-V6 assembly shown in the photographs.
What it adds to the ho..
0.85€
Ex Tax:0.70€
Stock: In Stock
Model: Calcetin-vol
Insulating silicone sock for Volcano-type heater blocks. It wraps around the hot section to reduce heat loss, limit the direct effect of part-cooling airflow and help keep the heater block cleaner.
Main benefits
Thermal insulation: reduces heat loss from the block surface.
Imp..
0.60€
Ex Tax:0.50€
Stock: In Stock
Model: Aislante Silicona Hotend
Silicone sock for the V6 heating block, its main advantages that keeps the nozzle clean and helps maintain temperature.Features:Manufactured from a non-stick silicone material, heat resistant, it will repel the accumulation of molten plastic. What helps with sticky materials and materials that tend ..
0.50€
Ex Tax:0.41€
Stock: In Stock
Model: Orbiter-V2.5-upgrade
This Orbiter V2.5 upgrade kit updates the transmission of an existing Orbiter V2.0 extruder without replacing the full assembly. It adds the revised drive-gear geometry, a pre-assembled spider shaft, planetary gears and moulded gear housing.
Important: this is a mechanical upgrade kit, not a comple..
35.99€
Ex Tax:29.74€
Stock: In Stock
Model: Thermistor-PT1000-barehead-Rapido2F
Replacement PT1000 Bare Head temperature sensor for the Phaetus RAPIDO 2F hotend. It replaces the original sensor while retaining the PT1000 RTD measurement system intended for this hotend.
Features
Type: PT1000 RTD sensor.
Replaceable Bare Head format.
Designed for the Phaetus RAPIDO 2F syste..
10.89€
Ex Tax:9.00€
Stock: In Stock
Model: Teflon-tube-4/2.5-1m
This PTFE guide tube has a 4 mm outer diameter and a 2.5 mm inner diameter. It is suitable for guiding 1.75 mm filament in 3D printers, Bowden extrusion systems and auxiliary paths between the spool, a dry box and the extruder.
Its inner diameter provides more clearance than a conventional 4 × 2 ..
1.02€
Ex Tax:0.84€
Stock: In Stock
Model: Teflon-tube-4/3-1m
This PTFE guide tube has nominal dimensions of 4 mm outer diameter and 3 mm inner diameter. Its wide internal passage makes it suitable as a low-restriction filament guide, particularly between a spool or dry box and the extruder.
It can be used with 1.75 mm filament when a generous clearance is ..
0.80€
Ex Tax:0.66€