Stock: In Stock
Model: GT2-20T-noteeth-ID3-Bearing
Smooth idler pulley with an integrated bearing and a nominal 20T-equivalent size, intended to guide the back of a 6 mm GT2 belt on a 3 mm axle or screw.
Compared with the 16T-size version, it provides a larger belt path radius but also requires more space. Pulley size is part of the mechanism geo..
0.99€
Ex Tax:0.82€
Stock: In Stock
Model: GT2-20T-noteeth-ID5-Bearing
Smooth idler pulley for 6 mm GT2 belts, with an aluminium body, integrated bearing and nominal 5 mm bore. The 20T designation identifies its reference size, although the contact surface has no teeth.
Specifications
Intended belt profile: GT2, 2 mm pitch.
Surface: smooth, without teeth.
Refer..
0.99€
Ex Tax:0.82€
Only a few units in stock
-9 %
Stock: In Stock
Model: Spindle-775-288W
The HANPOSE 775-288W is a brushed DC, double-ball-bearing, double-shaft motor for building compact spindles in small CNC machines, engravers and bench tools. It is the fastest member of this family, with declared no-load reference speeds of 6,000rpm at 12V and 12,000rpm at 24V.
Its 5 × 16mm round f..
14.25€ 12.99€
Ex Tax:10.74€
Stock: In Stock
Model: Spindle-775-80W
The HANPOSE 775-80W is a brushed DC motor with two ball bearings, intended as the drive unit for a compact spindle in small CNC machines, engravers and bench tools. Its 5mm round front shaft accepts a suitable chuck or collet adapter, while its rear shaft and internal fan identify this double-shaft ..
12.75€
Ex Tax:10.54€
Stock: In Stock
Model: Spindle-895-200W
The HANPOSE 895-200W is a brushed DC motor in the larger 895 housing, with dual ball bearings and a double shaft, intended for building spindles for small CNC machines and bench tools. Compared with the 775 models in this family it has lower declared speed and a higher torque figure: 3,000rpm at 12V..
21.75€
Ex Tax:17.98€
Stock: In Stock
Model: 3DSteel-NutsAndBolts
Complete hardware kit prepared for HTA3D 3DSteel V1 and 3DSteel V2 3D printers. It includes the fasteners used for the main structure and several machine subassemblies.
Components are grouped by size to make identification easier during assembly, maintenance or rebuilding.
Main features
..
5.99€
Ex Tax:4.95€
-73 %
Stock: In Stock
Model: P3Steel_HTA3D_HardwareSet
Hardware kit prepared for assembling and maintaining an HTA3D P3Steel 3D printer with a single-extruder configuration. It brings together the screws, nuts, washers and bed springs used in this version of the machine.
Suitable for building an HTA3D P3Steel, replacing worn hardware or keeping a mat..
20.00€ 5.35€
Ex Tax:4.42€
-71 %
Stock: In Stock
Model: P3Steel Dual HTA3D HardwareSet
Hardware kit prepared for an HTA3D P3Steel Dual 3D printer. It includes the additional fasteners used by this dual-extrusion build and combines its screws, nuts, washers and springs in one organised set.
The Dual version uses different quantities and a different combination of fasteners from the ..
20.00€ 5.75€
Ex Tax:4.75€
Stock: In Stock
Model: Termorretractil
Heat shrink tubing is a flexible sleeve designed to insulate, protect and identify electrical connections. When heated, the tubing shrinks around the cable or component, providing a clean finish and additional protection against wear and abrasion.
Features
Excellent electrical insulation..
0.12€
Ex Tax:0.10€
Stock: In Stock
Model: CamaCaliente-sujecion
Hardware kit for mounting and levelling a 3D-printer heated bed with four countersunk holes. It includes M3 screws, compression springs, wide washers and self-locking nuts to create four adjustable mounting points.
The springs allow the distance between the heated bed and Y carriage to be adjuste..
1.50€
Ex Tax:1.24€
5 - 10 Days
Stock: 5 - 10 Days
Model: FCMini-XH2.54-Horizontal
Mini mechanical endstop with horizontal connector, metal lever, LED indicator and an approximately 1 m cable. Its narrow PCB helps integration into 3D printers, small CNC machines and mechanisms with limited sensor clearance.
Features
Snap-action microswitch with metal lever.
Co..
0.99€
Ex Tax:0.82€
Out of Stock
Stock: Out of Stock
Model: Kit-Bloque-Kobra3
Replacement assembly for the hotend fitted to the Anycubic Kobra 3 and Kobra 3 Combo. It is supplied assembled with a heater block, heater cartridge, thermistor, bimetal heatbreak, 0.4 mm Brass nozzle and silicone sock.
It is intended to connect to the original Kobra 3 printhead. It should not be..
12.70€
Ex Tax:10.50€