New
Stock: In Stock
Model: MELLOW-CAN-EXP
The Mellow FLY CANBus Expand organises connections for up to four CAN boards and distributes their power from one common point. It is useful for 3D printers with toolhead electronics, multi-tool projects and installations where accessible, labelled connections are preferable to scattered wire splice..
11.95€
Ex Tax:9.88€
New
Stock: In Stock
Model: MELLOW-ADXL345-USB
The Mellow FLY ADXL345 USB is a compact accelerometer for measuring a 3D printer's resonances with Klipper and tuning Input Shaper. It combines a three-axis ADXL345 sensor and an RP2040 microcontroller on a USB-C board: measurements are acquired locally and sent over USB to the computer running Klip..
9.99€
Ex Tax:8.26€
New
Stock: In Stock
Model: MELLOW-C8P-M2WE
The Mellow FLY C8Pro with M2WE combines the computer running Klipper and the motion-control electronics on one board. It features a quad-core Allwinner H618 with 1 GB RAM, an STM32H723 ARM Cortex-M7, eight independent driver sockets and connections for heaters, fans, probes and CAN toolboards.
This..
114.95€
Ex Tax:95.00€
New
Stock: In Stock
Model: MELLOW-SHT36-V3P
The Mellow FLY SHT36 V3 Plus brings extruder motor, heater, fan and sensor connections together on the printhead. Its CAN or RS232 link carries power and communication over four conductors, reducing the wiring harness travelling with the toolhead and helping create a tidier installation.
The defini..
34.95€
Ex Tax:28.88€
Stock: In Stock
Model: 3MOS-MKS
The MKS 3MOS V1.0 converts a spare stepper-driver socket into three independently controlled fan outputs. It repurposes the socket's ENABLE, STEP and DIR signals to control FAN1, FAN2 and FAN3 respectively, making it particularly useful on boards with more axes than the printer requires.
This is ..
2.70€
Ex Tax:2.23€
Only a few units in stock
Clearance
-24 %
Stock: In Stock
Model: Eagle-MKS
The Makerbase MKS Eagle V1.0 is a 32-bit controller board for 3D printers and custom machines with five on-board TMC2209 drivers connected through UART. It combines a 168 MHz STM32F407 microcontroller, expanded storage, dual-extruder connections and official support for Marlin 2 and Klipper.
Its ..
52.50€ 39.99€
Ex Tax:33.05€
Stock: In Stock
Model: MKS-PI
The MKS Pi V1.1 is a 64-bit host computer designed by Makerbase to run Klipper without relying on a Raspberry Pi. It integrates a quad-core Rockchip RK3328 SoC, 1 GB of DDR3 memory, Ethernet, three USB ports, HDMI and a direct 12/24 V input, making it particularly convenient for installation inside ..
48.50€
Ex Tax:40.08€
Only a few units in stock
-13 %
Stock: In Stock
Model: Modulo-Wifi-MKS
The MKS TFT WiFi V1.0 module adds 2.4 GHz wireless connectivity to compatible Makerbase touchscreens. It combines an ESP8266-based ESP-12S with the 2 × 4 MKS TFT WiFi host connector.
With suitable firmware it can work with compatible LAN tools, send files to storage managed by the screen and rela..
8.00€ 6.99€
Ex Tax:5.78€
Stock: In Stock
Model: dual-axis-module
This parallel stepper motor splitter module connects two four-wire bipolar motors to a single controller-board motor output. It is commonly used on 3D printers with two Z-axis motors, although it can also serve other axes or mechanisms where two motors must move simultaneously from the same driver.
..
1.25€
Ex Tax:1.03€
-20 %
Stock: In Stock
Model: CajaRamps-3DSteel
Printed enclosure designed to install and protect the RAMPS 1.4-based electronics used by the HTA3D 3DSteel 3D printer.
Its geometry allows it to be attached to the machine frame, keeps the electronic components protected and provides room for organising surplus wiring. It is printed in PLA.
..
7.50€ 6.00€
Ex Tax:4.96€
-20 %
Stock: In Stock
Model: Caja-Electronica-3DSteel-V2
Printed enclosure designed to install and protect the BIGTREETECH SKR V1.4 board used by the HTA3D 3DSteel V2 3D printer.
It attaches to the machine frame and helps keep the electronics protected and the wiring organised. It is printed in PLA, with geometry designed for the SKR 1.4 installation u..
7.50€ 6.00€
Ex Tax:4.96€
Stock: In Stock
Model: RAMPS1.4
RAMPS 1.4, short for RepRap Arduino Mega Pololu Shield, is an expansion board for building modular controllers based on the Arduino Mega 2560. It provides connections for stepper motors, endstops, thermistors, a hotend, heated bed, fans, servos and other components commonly used in RepRap 3D printer..
6.65€
Ex Tax:5.50€