Out of Stock
Stock: Out of Stock
Model: SBCAN-Fysetc
The FYSETC SB CAN ToolHead V1.3 brings the StealthBurner printhead electronics together on one board. It controls the extruder motor through an integrated TMC2209 driver, the heater and temperature sensor, two fans, RGB lighting, and inputs for a probe or endstop. An onboard ADXL345 supports Klipper..
34.50€
Ex Tax:28.51€
Stock: In Stock
Model: Spider3-Fysetc-X-Voron
The FYSETC Spider V3.0 F446 is a 32-bit control board designed for 3D printers with many motors and peripherals. It combines a 180 MHz STM32F446, eight replaceable driver sockets, three hotend outputs, one bed output, six fan connectors and an onboard CAN transceiver in a compact 155.3 × 76.5 mm for..
69.99€
Ex Tax:57.84€
Out of Stock
Stock: Out of Stock
Model: UCAN-Fysetc
The FYSETC UCAN V1.0 connects a host computer over USB-C to a CAN bus used by compatible toolhead boards and other modules. It is based on an STM32F072 and has a pluggable terminal for CAN_H, CAN_L and GND. In a Klipper installation, it provides host communication with CAN nodes; it does not replace..
13.25€
Ex Tax:10.95€
Out of Stock
Stock: Out of Stock
Model: mosfet-module
This IRF520 MOSFET module can control DC loads using a signal from an Arduino, ESP32, Raspberry Pi, controller board or other microcontroller. It can be used to switch or regulate devices such as fans, LED lighting, small pumps and other low-voltage accessories using PWM.
The module simplifies MO..
1.75€
Ex Tax:1.45€
Out of Stock
Stock: Out of Stock
Model: Gen_L
Makerbase MKS Gen_L V2.1 is an 8-bit FDM 3D-printer controller combining Arduino Mega 2560/RAMPS-style architecture on one PCB. It provides five X, Y, Z, E0 and E1 driver sockets, USB, endstop and temperature-sensor inputs, outputs for a bed, two hotends and a fan, and display connectors. The PCB si..
24.00€
Ex Tax:19.83€
Stock: In Stock
Model: 3MOS-MKS
The MKS 3MOS V1.0 converts a spare stepper-driver socket into three independently controlled fan outputs. It repurposes the socket's ENABLE, STEP and DIR signals to control FAN1, FAN2 and FAN3 respectively, making it particularly useful on boards with more axes than the printer requires.
This is ..
2.70€
Ex Tax:2.23€
Only a few units in stock
Clearance
-24 %
Stock: In Stock
Model: Eagle-MKS
The Makerbase MKS Eagle V1.0 is a 32-bit controller board for 3D printers and custom machines with five on-board TMC2209 drivers connected through UART. It combines a 168 MHz STM32F407 microcontroller, expanded storage, dual-extruder connections and official support for Marlin 2 and Klipper.
Its ..
52.50€ 39.99€
Ex Tax:33.05€
Stock: In Stock
Model: MKS-PI
The MKS Pi V1.1 is a 64-bit host computer designed by Makerbase to run Klipper without relying on a Raspberry Pi. It integrates a quad-core Rockchip RK3328 SoC, 1 GB of DDR3 memory, Ethernet, three USB ports, HDMI and a direct 12/24 V input, making it particularly convenient for installation inside ..
48.50€
Ex Tax:40.08€
Out of Stock
Stock: Out of Stock
Model: Robin-Nano
The MKS Robin Nano V3.1 is a 32-bit control board for building or upgrading a 3D printer's electronics. This revision uses an STM32F407VET6 at 168 MHz, with 512 KB flash and 192 KB RAM, and accepts replaceable stepper drivers. It offers connections for two extruders, a heated bed, display, fans and ..
41.75€
Ex Tax:34.50€
Only a few units in stock
-13 %
Stock: In Stock
Model: Modulo-Wifi-MKS
The MKS TFT WiFi V1.0 module adds 2.4 GHz wireless connectivity to compatible Makerbase touchscreens. It combines an ESP8266-based ESP-12S with the 2 × 4 MKS TFT WiFi host connector.
With suitable firmware it can work with compatible LAN tools, send files to storage managed by the screen and rela..
8.00€ 6.99€
Ex Tax:5.78€
Stock: In Stock
Model: dual-axis-module
This parallel stepper motor splitter module connects two four-wire bipolar motors to a single controller-board motor output. It is commonly used on 3D printers with two Z-axis motors, although it can also serve other axes or mechanisms where two motors must move simultaneously from the same driver.
..
1.25€
Ex Tax:1.03€
-20 %
Stock: In Stock
Model: CajaRamps-3DSteel
Printed enclosure designed to install and protect the RAMPS 1.4-based electronics used by the HTA3D 3DSteel 3D printer.
Its geometry allows it to be attached to the machine frame, keeps the electronic components protected and provides room for organising surplus wiring. It is printed in PLA.
..
7.50€ 6.00€
Ex Tax:4.96€