Stock: In Stock
Model: 3060-Profile-1m
Description
Anodised aluminium structural profile with a nominal 30 × 60 mm cross-section and a length of 1 metre. Its double section provides greater directional stiffness than a 3030 profile, making it suitable for bases, uprights, gantries and cross-members subjected to higher loads.
It has six..
27.50€
Ex Tax:22.73€
Stock: In Stock
Model: Kapton30mm
Kapton-type polyimide adhesive tape measuring 30mm wide and 33 metres long. It provides electrical insulation, thermal protection and masking for 3D printing, electronics, soldering and BGA or SMD rework.
It is made from polyimide film with a silicone adhesive and has a specified heat resistance ..
2.99€
Ex Tax:2.47€
Only a few units in stock
-25 %
Stock: In Stock
Model: Base-rugosa-33x33
330 × 330 mm Double-Sided Textured PEI Flexible Sheet
Flexible steel sheet with textured PEI on both sides for 3D printers using a compatible 330 × 330 mm magnetic base. Parts can be removed by gently flexing the sheet after it has cooled.
Nominal size: 330 × 330 mm.Base: flexible spring steel.Sur..
29.99€ 22.50€
Ex Tax:18.60€
Out of Stock
Stock: Out of Stock
Model: Energetic-base-33x33
The 330 × 330 mm flexible steel sheet with PEI/Ultem offers two printing finishes: a textured face and a smooth face. It sits on a suitable magnetic base and can be gently flexed after cooling to help remove printed parts.
Key features
Nominal size: 330 × 330 mm.
Substrate: flexible spr..
64.99€
Ex Tax:53.71€
New
Stock: In Stock
Model: CC-Silicona350x350-220V
350 × 350 mm, 220 V, 750 W adhesive silicone heater for large-format 3D-printer beds, wired with approximately 1 m leads and an XH2.54 100K NTC.Mains voltage: requires professional installation, AC switching, fuse/breaker, RCD, protective earth and an independent thermal fuse. It cannot be driven di..
37.50€
Ex Tax:30.99€
Stock: In Stock
Model: Energetic-base-35x35
350 × 350 mm Flexible Steel Sheet with PEI on Both Sides
Flexible spring-steel sheet for a magnetic bed, coated with PEI/Ultem on both sides. It is intended for large print surfaces and allows parts to be removed by flexing the sheet after the bed cools.
Nominal size: 350 × 350 mm.Base material: f..
67.50€
Ex Tax:55.79€
-11 %
Stock: In Stock
Model: 3Dtouch
The 3DTouch is an automatic bed leveling sensor for 3D printers. During the print preparation process, the probe detects the position of the print surface to help compensate for possible height differences between different points of the build plate.
This version features a non-metallic probe and..
13.99€ 12.45€
Ex Tax:10.29€
New
Stock: In Stock
Model: Destornilladores-Allen
Set of four metric hex drivers in 1.5, 2.0, 2.5 and 3.0 mm sizes. Their straight-handle format is convenient for assembling, adjusting and maintaining 3D printers, RC models, small mechanisms, electronics enclosures and DIY projects that use internal-hex fasteners.
Each tool has a straight hex ti..
11.99€
Ex Tax:9.91€
Stock: In Stock
Model: CableMotor-DuPont-0.5m
Description
Short four-conductor cable for connecting a stepper motor to a controller board or driver through DuPont-type terminals. It has a 2.0 mm pitch PH-type connector on the motor end.
Its 0.5 metre length is suitable for compact assemblies, test benches and machines where the motor is locat..
0.69€
Ex Tax:0.57€
Stock: In Stock
Model: CableMotor-DuPont-1m
Description
Four-conductor cable for connecting a stepper motor to electronics through a DuPont-type connection. It has a 2.0 mm pitch PH-type connector for the motor and a DuPont connection on the controller or driver end.
The 1 metre length is suitable for 3D printers, prototypes, test benches a..
0.79€
Ex Tax:0.65€
Out of Stock
Stock: Out of Stock
Model: CableMotor-XH2.54-0.5m
Description
Short four-conductor cable for connecting a stepper motor to a controller board or driver. It has a 2.0 mm pitch PH-type connector for the motor and a four-position XH-type connector for the electronics.
The 0.5 metre length is suitable when the motor is located close to the controller..
0.69€
Ex Tax:0.57€
Stock: In Stock
Model: CableMotor-XH2.54-1m
Description
Four-conductor cable for connecting a stepper motor to a controller board or driver. It has a 2.0 mm pitch PH-type connector on the motor end and a four-position XH-type connector on the electronics end.
Its 1 metre length is suitable for many 3D printers, small CNC machines, laser eng..
0.79€
Ex Tax:0.65€