Stock: In Stock
Model: Sherpa-V1.5
The FYSETC Sherpa Mini V1.5 is a compact 1.75mm filament extruder supplied with a NEMA 14 motor and dual-drive filament gears. Its small package is particularly useful for direct-drive toolheads where moving mass must be limited without giving up a geared transmission.
This revision combines an 8..
47.50€
Ex Tax:39.26€
Stock: In Stock
Model: Spider3-Fysetc-X-Voron
The FYSETC Spider V3.0 F446 is a 32-bit control board designed for 3D printers with many motors and peripherals. It combines a 180 MHz STM32F446, eight replaceable driver sockets, three hotend outputs, one bed output, six fan connectors and an onboard CAN transceiver in a compact 155.3 × 76.5 mm for..
69.99€
Ex Tax:57.84€
Stock: In Stock
Model: TMC2130-SPI-Fysetc
The FYSETC TMC2130 V1.2 is a bipolar stepper motor driver prepared for SPI operation. In addition to STEP and DIR motion signals, firmware can configure current, microsteps and operating mode, read diagnostics and use StallGuard2 when the controller board also routes the required signals correctly.
..
5.50€
Ex Tax:4.55€
Stock: In Stock
Model: TMC2208-Fysetc
The FYSETC TMC2208 V1.2 is a StepStick driver for two-phase bipolar stepper motors, designed to substantially reduce motion noise and provide accurate control in 3D printers, small CNC machines, robots and automation projects. It can operate through standard STEP/DIR signals or use UART to configure..
4.35€
Ex Tax:3.60€
Out of Stock
Stock: Out of Stock
Model: UCAN-Fysetc
The FYSETC UCAN V1.0 connects a host computer over USB-C to a CAN bus used by compatible toolhead boards and other modules. It is based on an STM32F072 and has a pluggable terminal for CAN_H, CAN_L and GND. In a Klipper installation, it provides host communication with CAN nodes; it does not replace..
13.25€
Ex Tax:10.95€
Stock: In Stock
Model: 1225B-BallBearing-24V
GDSTIME 12025 24V axial fan measuring 120 × 120 × 25 mm and equipped with dual ball bearings. It is designed to provide high airflow in electrical cabinets, electronics enclosures, enclosed 3D printers, CNC machines and other large-format ventilation systems.
This version has a nominal speed of 3..
5.99€
Ex Tax:4.95€
Stock: In Stock
Model: 12025-Hydraulic-24V
GDSTIME 12025 24V axial fan measuring 120 × 120 × 25 mm and equipped with a hydraulic bearing. It provides large-format ventilation with a balance focused on reducing noise and electrical consumption.
Its nominal speed of 2000 RPM and stated airflow of 77 CFM make it suitable for electronics encl..
3.50€
Ex Tax:2.89€
Stock: In Stock
Model: 12032Blower-BallBearing-24V
GDSTIME 12032 24V centrifugal blower fan with dual ball bearings, a 2-pin XH2.54 connector and a 30 cm cable. Its 120 × 120 × 32 mm format provides substantially more airflow than the compact blowers commonly used on print heads.
It is intended for ventilating enclosures, electronics, machines, f..
11.99€
Ex Tax:9.91€
Stock: In Stock
Model: Cable-XH2.54-1m
GDSTIME extension cable designed to add one metre to the connection of a two-wire fan. It has complementary male and female 2-pin XH2.54 connectors, providing a detachable connection without cutting or soldering the fan's original cable.
Main features
Brand: GDSTIME.
Nominal length: 1 m..
0.99€
Ex Tax:0.82€
Stock: In Stock
Model: 12032Blower-Sleeve-24V
Large-format GDSTIME centrifugal blower powered from 24 V and measuring a nominal 120 × 120 × 32 mm. Its airflow and pressure make it suitable for ducts, filtration, electronics cooling and larger-scale local ventilation than the blowers normally fitted around hotends.
Specifications
Brand: GD..
9.59€
Ex Tax:7.93€
Stock: In Stock
Model: 4020Blower-24V
GDSTIME 24 V centrifugal blower in a 4020 format, with a sleeve bearing and an approximately 20 cm cable. Its 20 mm thickness provides static pressure in a compact assembly suitable for nozzles, air ducts and localised cooling.
Specifications
Brand: GDSTIME.
Format: 4020.
Nominal dimensions:..
3.50€
Ex Tax:2.89€
Stock: In Stock
Model: 5015s-24v
GDSTIME 5015-format centrifugal blower powered from 24 V and fitted with a hydraulic bearing system. Its side outlet is designed for air ducts and nozzles, providing localised cooling in 3D printers, electronics and compact equipment.
Specifications
Brand: GDSTIME.
Format: 5015.
Nominal dime..
3.15€
Ex Tax:2.60€