Stock: In Stock
Model: ADXL345 V2.0
The BIGTREETECH ADXL345 V2.0 is a USB accelerometer designed to measure a 3D printer's resonances and help calibrate Input Shaper in Klipper. It combines an ADXL345 sensor with its own RP2040 microcontroller, allowing it to connect to the Klipper host over USB-C without routing SPI signals to the ma..
11.35€
Ex Tax:9.38€
-14 %
Out of Stock
Stock: Out of Stock
Model: BTT02-V1.0
The BIGTREETECH BTT002 V1.0 is a 32-bit controller board developed as a configurable alternative to the Einsy Rambo used by the Original Prusa i3 MK3S. It features a 168 MHz STM32F407VGT6 microcontroller, runs from 12 or 24 V and uses replaceable StepStick drivers instead of soldered motor drivers.
..
69.99€ 59.99€
Ex Tax:49.58€
Only a few units in stock
-18 %
Stock: In Stock
Model: BTT-CB1
The BIGTREETECH CB1 V2.2 with 1 GB RAM is a compact computer module designed to run Linux and act as a host for Klipper, Moonraker and Mainsail on compatible carrier boards. It combines a quad-core 1.5 GHz Allwinner H616 Cortex-A53 processor with 2.4 GHz Wi-Fi and provides the signals required for a..
36.75€ 29.99€
Ex Tax:24.79€
Out of Stock
Stock: Out of Stock
Model: BTT-CB2
The BIGTREETECH CB2 V1.0 is a computer module for running Linux and Klipper on a compatible carrier board such as a Manta. It has a quad-core Rockchip RK3566, 2 GB of LPDDR4 RAM, 32 GB of onboard eMMC storage and 2.4/5 GHz Wi-Fi. Its mounting format and two underside connectors follow the Raspberry ..
53.50€
Ex Tax:44.21€
Stock: In Stock
Model: DCDC5V-Module
The BIGTREETECH DCDC MODE V1.0 is a DC-DC step-down module designed to provide a stable 5 V output at up to 3 A for peripherals connected to SKR V1.4 and SKR V1.4 Turbo control boards.
It converts the printer's main 12 or 24 V supply and reduces the load placed on the control board's integrated 5..
5.75€
Ex Tax:4.75€
Stock: In Stock
Model: E3-RRF
The BIGTREETECH E3 RRF V1.1 is a 32-bit controller board designed to upgrade Ender-3-family printers and machines using a compatible electronics footprint. It combines a 168 MHz STM32F407VGT6, four integrated UART TMC2209 drivers and an onboard ESP8266 Wi-Fi module.
It can run Marlin or RepRapFirmw..
69.99€
Ex Tax:57.84€
Stock: In Stock
Model: EBB36 CAN Max31865
The BIGTREETECH EBB36 CAN V1.2 is a printhead toolboard designed around 36 mm extruder stepper motors. It centralises the motor, heater, fan and sensor connections on the toolhead, reducing the number of wires running through the printer.
This version includes a MAX31865 interface for 2-wire or 4..
21.25€
Ex Tax:17.56€
Out of Stock
Stock: Out of Stock
Model: EBB36 CAN No Max31865
The BIGTREETECH EBB36 CAN V1.2 is a printhead toolboard designed around 36 mm extruder stepper motors. It centralises the extruder motor, heater, fan and sensor connections and communicates with Klipper through CAN BUS or USB.
This version does not include a MAX31865 interface. Its TH0 input supp..
15.99€
Ex Tax:13.21€
New
Stock: In Stock
Model: EBB36 GEN 2
The BIGTREETECH EBB36 GEN2 V1.0 is a new-generation toolboard for compact toolheads using 36 mm extruder stepper motors. It centralises the motor, heater, fan, probe and sensor connections through a single CAN BUS or USB communication link.
The GEN2 revision features a 64 MHz STM32G0B1 microcontr..
35.75€
Ex Tax:29.55€
Stock: In Stock
Model: EBB42 CAN Max31865
The BIGTREETECH EBB42 CAN V1.2 is a toolboard designed for installation around 42 mm extruder stepper motors. It centralises the motor, heater, fan and sensor connections on the toolhead and communicates with Klipper through CAN BUS or USB.
This version includes a MAX31865 interface and supports ..
21.25€
Ex Tax:17.56€
Stock: In Stock
Model: EBB42 CAN No Max31865
The BIGTREETECH EBB42 CAN V1.2 is a printhead toolboard designed for installation around 42 mm extruder stepper motors. It moves the extruder, heater, fan and sensor connections to the toolhead and communicates with Klipper through CAN BUS or USB.
This version does not include a MAX31865 interfac..
15.99€
Ex Tax:13.21€
New
Stock: In Stock
Model: EBB42 GEN 2
The BIGTREETECH EBB42 GEN2 V1.0 is a new-generation toolboard designed for installation around 42 mm extruder stepper motors. It centralises the motor, heater, fan, sensor and probe connections on the toolhead and communicates with Klipper through CAN BUS or USB.
It features a 64 MHz STM32G0B1 mi..
35.75€
Ex Tax:29.55€