Menu
Your Cart

Replacement Heater Block for Phaetus RAPIDO 2F

Replacement Heater Block for Phaetus RAPIDO 2F
Replacement Heater Block for Phaetus RAPIDO 2F
Out of Stock
Replacement Heater Block for Phaetus RAPIDO 2F
Replacement Heater Block for Phaetus RAPIDO 2F
Replacement Heater Block for Phaetus RAPIDO 2F
0 reviews - Write a review
27.45€
Ex Tax: 22.69€
  • Stock: Out of Stock
  • Model: Block-Rapido2F
Phaetus Phaetus
Add to Cart
Add to Wish List
Product out of stock
This product is out of stock, we will try to replenish it as soon as possible. You can request a notice by clicking on the green button (except discontinued products).

Original replacement heater block for the Phaetus RAPIDO 2F hotend. It replaces a damaged block during repair or maintenance while preserving the melting-zone geometry designed for this specific model.

Features

  • Specific replacement part for the Phaetus RAPIDO 2F hotend.
  • Extended heating-zone design.
  • Designed to work with the RAPIDO 2F rectangular ceramic heater.
  • Compatible with the replaceable PT1000 sensor used by this hotend.
  • Supports repair and maintenance of the heating system.

Compatibility

Compatibility is confirmed for the Phaetus RAPIDO 2.0F UHF hotend. It must not be assumed to fit the first-generation RAPIDO, RAPIDO 2, RAPIDO 2 Plus, RAPIDO ACE or other Phaetus hotends, even if their appearance or product names are similar.

Before ordering, confirm that the installed hotend is exactly the RAPIDO 2F version and compare the block geometry, connections and heating-system revision.

Related components

Performance and installation

The extended heating zone is part of the RAPIDO 2F high-flow design. Final performance depends on the complete assembly: heater block, ceramic heater, PT1000 sensor, nozzle, heatbreak, filament, temperature and printing parameters.

Replacement must be performed with the hotend cold and disconnected. After installation, check the heater and sensor fastening, inspect the wiring and perform the thermal calibration recommended by the printer firmware.

Write a review

Note: HTML is not translated!
Bad Good
Captcha
Tags: heating, blocks, spares, for, hotend, phaetus
Quickview
100K NTC Beta 3950 Thermistor with 1 m Cable and Dupont Connector
100K NTC Beta 3950 Thermistor with 1 m Cable and Dupont Connector
100K NTC Beta 3950 thermistor for temperature measurement in hotends, heated beds and other compatible thermal control systems. It is supplied pre-wir..
0.65€ Ex Tax:0.54€
Add to Cart
Add to Wish List
Quickview
3 mm Encapsulated 100K NTC Beta 3950 Thermistor with 1 m Cable and Dupont Connector
3 mm Encapsulated 100K NTC Beta 3950 Thermistor with 1 m Cable and Dupont Connector
100K NTC Beta 3950 hotend thermistor protected by a 3 mm cylindrical 304 stainless-steel capsule. The encapsulation provides a more robust installatio..
0.85€ Ex Tax:0.70€
Add to Cart
Add to Wish List
Quickview
3 mm Encapsulated 100K NTC Beta 3950 Thermistor with 1 m Cable and XH Connector
3 mm Encapsulated 100K NTC Beta 3950 Thermistor with 1 m Cable and XH Connector
100K NTC Beta 3950 hotend thermistor with a 3 mm cylindrical 304 stainless-steel capsule, 1 metre cable and XH connector. Its encapsulated constructio..
0.85€ Ex Tax:0.70€
Add to Cart
Add to Wish List
Quickview
100K NTC Beta 3950 Thermistor with 1 m Cable and XH Connector
100K NTC Beta 3950 Thermistor with 1 m Cable and XH Connector
Pre-wired 100K NTC Beta 3950 thermistor for temperature measurement in compatible hotends, heated beds and thermal control projects. It includes a 1 m..
0.65€ Ex Tax:0.54€
Add to Cart
Add to Wish List
Quickview
Phaetus RAPIDO 2 HF Blue Hotend for 1.75 mm Filament
-4 % Out of Stock
Phaetus RAPIDO 2 HF Blue Hotend for 1.75 mm Filament
Phaetus RAPIDO 2 hotend in the HF high-flow configuration, featuring a blue heatsink and designed for 1.75 mm filament. Its extended heating zone is i..
99.00€ 94.99€ Ex Tax:78.50€
Add to Cart
Add to Wish List
Quickview
Phaetus RAPIDO 2 UHF Black Hotend for 1.75 mm Filament
Only a few units in stock -6 %
Phaetus RAPIDO 2 UHF Black Hotend for 1.75 mm Filament
Phaetus RAPIDO 2 hotend in the UHF ultra-high-flow configuration, featuring a black heatsink and designed for 1.75 mm filament. Its extended melting z..
105.99€ 99.99€ Ex Tax:82.64€
Add to Cart
Add to Wish List
Quickview
Fresa 3D 104NT-4 Thermistor with 100 mm Cable and GH1.25 Connector
Fresa 3D 104NT-4 Thermistor with 100 mm Cable and GH1.25 Connector
Fresa 3D 104NT-4 thermistor with a 100 mm cable and 2-pin GH1.25 connector. It is designed for temperature measurement systems compatible with the 104..
3.35€ Ex Tax:2.77€
Add to Cart
Add to Wish List
Quickview
60 W ceramic hotend kit for Creality K1 and K1 Max — 0.4 mm nozzle
60 W ceramic hotend kit for Creality K1 and K1 Max — 0.4 mm nozzle
60 W ceramic hotend kit for replacing the heating and melt-zone assembly on Creality K1 and K1 Max printers fitted with the matching earlier-generatio..
11.60€ Ex Tax:9.59€
Add to Cart
Add to Wish List
Quickview
BIGTREETECH Hermit Crab V2.0 CAN - quick toolhead change with 3 plates for Klipper
BIGTREETECH Hermit Crab V2.0 CAN - quick toolhead change with 3 plates for Klipper
The BIGTREETECH Hermit Crab V2.0 CAN is a manual quick-change platform designed to keep several toolheads prepared and swap them without dismantling e..
158.50€ Ex Tax:130.99€
Add to Cart
Add to Wish List
Quickview
Brass V6 Heater Block for 3 mm Encapsulated Sensors, M6 Thread
Brass V6 Heater Block for 3 mm Encapsulated Sensors, M6 Thread
Brass V6 heater block designed for temperature sensors with a 3 mm cylindrical encapsulation. Brass provides greater mechanical strength and higher th..
4.85€ Ex Tax:4.01€
Add to Cart
Add to Wish List
Quickview
Trianglelab CHC B3950 24 V — ceramic heater core with integrated thermistor
Trianglelab CHC B3950 24 V — ceramic heater core with integrated thermistor
Trianglelab 24 V CHC ceramic heater core with an integrated NTC 100K B3950 thermistor. It replaces the separate block, heater cartridge and sensor wit..
19.50€ Ex Tax:16.12€
Add to Cart
Add to Wish List
Quickview
Trianglelab CHC Pro B3950 24 V — Volcano-type ceramic core, 115 W max.
Trianglelab CHC Pro B3950 24 V — Volcano-type ceramic core, 115 W max.
Trianglelab 24 V CHC Pro ceramic heater core with an integrated NTC 100K B3950 thermistor and a declared maximum power of 115 W. Its extended body cre..
25.50€ Ex Tax:21.07€
Add to Cart
Add to Wish List
Quickview
V6 Heater Block for 3 mm Encapsulated Sensors, M6 Thread
V6 Heater Block for 3 mm Encapsulated Sensors, M6 Thread
V6-format heater block designed to accommodate temperature sensors with a nominal 3 mm cylindrical encapsulation, including NTC thermistors and RTD se..
0.90€ Ex Tax:0.74€
Add to Cart
Add to Wish List
Quickview
V6 Heater Block with M6 Thread Compatible with V5 and V6 Hotends
V6 Heater Block with M6 Thread Compatible with V5 and V6 Hotends
V6-format heater block designed to secure the heater cartridge and thermistor using independent clamping systems. This configuration provides stable i..
0.60€ Ex Tax:0.50€
Add to Cart
Add to Wish List