Out of Stock
Stock: Out of Stock
Model: SBCAN-Fysetc
The FYSETC SB CAN ToolHead V1.3 brings the StealthBurner printhead electronics together on one board. It controls the extruder motor through an integrated TMC2209 driver, the heater and temperature sensor, two fans, RGB lighting, and inputs for a probe or endstop. An onboard ADXL345 supports Klipper..
34.50€
Ex Tax:28.51€
Out of Stock
Stock: Out of Stock
Model: UCAN-Fysetc
The FYSETC UCAN V1.0 connects a host computer over USB-C to a CAN bus used by compatible toolhead boards and other modules. It is based on an STM32F072 and has a pluggable terminal for CAN_H, CAN_L and GND. In a Klipper installation, it provides host communication with CAN nodes; it does not replace..
13.25€
Ex Tax:10.95€
Out of Stock
Stock: Out of Stock
Model: 4010Blower-BallBearing-24V-1m
GDSTIME 4010 24V centrifugal blower fan with a ball bearing system and a 1 metre power cable. Its 40 × 40 × 10 mm format produces concentrated airflow through compact cooling ducts.
The ball bearing system is suitable for equipment subject to frequent or extended operation. The long cable simplif..
6.25€
Ex Tax:5.17€
5 - 10 Days
Stock: 5 - 10 Days
Model: FCMini-XH2.54-Horizontal
Mini mechanical endstop with horizontal connector, metal lever, LED indicator and an approximately 1 m cable. Its narrow PCB helps integration into 3D printers, small CNC machines and mechanisms with limited sensor clearance.
Features
Snap-action microswitch with metal lever.
Co..
0.99€
Ex Tax:0.82€
Out of Stock
Stock: Out of Stock
Model: Kit-Bloque-Kobra3
Replacement assembly for the hotend fitted to the Anycubic Kobra 3 and Kobra 3 Combo. It is supplied assembled with a heater block, heater cartridge, thermistor, bimetal heatbreak, 0.4 mm Brass nozzle and silicone sock.
It is intended to connect to the original Kobra 3 printhead. It should not be..
12.70€
Ex Tax:10.50€
Out of Stock
Stock: Out of Stock
Model: 3DSteel
The original HTA3D 3DSteel is a Cartesian DIY 3D printer kit developed as an evolution of our P3Steel. It combines a 3 mm steel frame, HTA3D V2 direct-drive extruder, dual Z lead screws and a 12 V control system based on Arduino Mega, RAMPS 1.6+ and TMC2130 drivers. Its open construction makes the m..
395.00€
Ex Tax:326.45€
Out of Stock
Stock: Out of Stock
Model: Conector-L 2020
Internal L-shaped metal connector designed to join two 20 series aluminium profiles at a 90° angle. Both arms fit inside the profile slots, leaving the outside surfaces of the structure unobstructed.
It provides a compact alternative to external brackets when a discreet joint is required and the ..
0.27€
Ex Tax:0.22€
Out of Stock
Stock: Out of Stock
Model: mosfet-module
This IRF520 MOSFET module can control DC loads using a signal from an Arduino, ESP32, Raspberry Pi, controller board or other microcontroller. It can be used to switch or regulate devices such as fans, LED lighting, small pumps and other low-voltage accessories using PWM.
The module simplifies MO..
1.75€
Ex Tax:1.45€
Discontinued
Stock: Discontinued
Model: MicroSD-64GB-Kingston
The 64GB Kingston Canvas Select Plus is a UHS-I microSDXC card for storing files and system images in devices that support this card format and capacity. The card pictured is marked SDCS2/64GB and carries Class 10, U1, V10 and A1 ratings.
It suits compatible Android devices, cameras and other micro..
8.99€
Ex Tax:7.43€
-8 %
Out of Stock
Stock: Out of Stock
Model: Orbiter-V2.5
The LDO Orbiter V2.5 is a compact, lightweight direct extruder for 1.75 mm filament. It combines a 36 mm LDO motor, planetary reduction and dual drive gears to feed filament accurately without adding excessive moving mass to the toolhead.
V2.5 retains the Orbiter V2.0 housing and architecture while..
75.99€ 69.99€
Ex Tax:57.84€
Out of Stock
Stock: Out of Stock
Model: Tuerca ranura 20-M3
Description
Nickel-plated carbon-steel M3 sliding nut for HTA3D European 20-series profiles with a nominal 6 mm slot. It is inserted through an open end and moved longitudinally to the required mounting position.
The M3 thread is useful for mounting sensors, small brackets, electronics and lightwe..
0.12€
Ex Tax:0.10€
Out of Stock
Stock: Out of Stock
Model: Inserto-M5
M5 Brass threaded insert for adding a durable, reusable metal thread to thermoplastic parts. Its Ø7 × 10mm body and bidirectional external knurling provide a large contact area with the surrounding material.
It is intended for larger printed components, mechanical brackets, enclosures and parts u..
0.34€
Ex Tax:0.28€